Jump to content
SAU Community

Wanted To Buy


Cubes

Recommended Posts

surge tank fittings are usually placed in the middle of the tank making the fuel inside just splash around etc

Swirl tanks are usually round with fittings placed on the end causing the fuel to "swirl" inside, there for fuel will always be available to the inlets/outlets.

Link to comment
Share on other sites

Marko go a swirl pot instead of a standard surge tank.

Outlaws in the city can help you, thats where i got mine but in a 4L

surge tank fittings are usually placed in the middle of the tank making the fuel inside just splash around etc

Swirl tanks are usually round with fittings placed on the end causing the fuel to "swirl" inside, there for fuel will always be available to the inlets/outlets.

Exactly what im looking at if nothing comes up by Friday, was going to put a baffle in a standard tank to stop it from splashing around otherwise tho. Ill give outlaws a call tomorrow, cheers for that. The one im looking at is on the net $100 for 2L tank

Link to comment
Share on other sites

Just to clarify on the fuel pump bit, as I just found out, ill be needing a minimum of a bosch 044 or equivalent and at least 2L capacity surge tank :( if anyone has anything let me know asap otherwise ill have to ditch more cash at the hunk and go buy new stuff this week :wacko:

Bosch 044 and bracket acquired, thanks a bunch to frankyp11 absolute champ!

Link to comment
Share on other sites

URGENT -

WTB - series 1 r33 type m front bar with indicators, and rear pods, preferably in the burgundy stock colour. would save a lot of headaches. still message me if you have in other colours.

will pay cash on pick up.

- few hundred dollars depending on condition and whether or not the front bar indicators are included. very keen for a quick buy so if you have this stuff message me.

Contact - msg me anytime on 0421549607

Link to comment
Share on other sites

WTB:

1: Bottom half of cluster surround or the entire trim

2: Drivers kick panel under the cluster surround

3: Trim that goes around the gearstick boot.

4: Main headlight switch

All parts are for a R32 GTS-T

PM me details or txt me on 0433 522 234

Cheers Tim

post-62269-0-95173100-1313907935_thumb.jpg

post-62269-0-05089900-1313908000_thumb.jpg

post-62269-0-92582200-1313908072_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...