Jump to content
SAU Community

What Non-genuine Windscreen & Windows Rubbers Fit My R32? Preparing To Paint My Car.


Recommended Posts

Gday,

Im preparing to strip my R32 gtst back to a shell so that i can have it resprayed. Im going to do all the prep work, and then tow it over to a spray painters to finnish it off.

My question is; Does anyone know what non genuine rubbers are able to be substituted for the factory R32 front and rear windscreen rubbers? Ive heard that some commodore rubbers will fit and im not prepared to pay $520 each for genuine Nissan ones! Also, ill pull the rear quarter windows out as well, so ill either have to remove the rubbers undamaged, or source some new ones. Does anyone know where i can get some of these as well (non genuine or cheap Nissan?).

Thanks,

Shaun.

the windscreen people will know... just take the rubber to them.?

what colour are you goin with the car?

When I repainted my R33 I had to get a new windscreen as well

The windscreen company used a mould similar to a my VX commadore and replaced the rear aswell

Cost about $30 for each.

When I repainted my R33 I had to get a new windscreen as well

The windscreen company used a mould similar to a my VX commadore and replaced the rear aswell

Cost about $30 for each.

Do they look the same though or does it look a bit weird...like they are not the right ones.

I am in the same position and will definately do this if they come up allright.

Cheers

Do they look the same though or does it look a bit weird...like they are not the right ones.

I am in the same position and will definately do this if they come up allright.

Cheers

Best thing is to drop into a windscreen shop and see what they have

Most the strips just come on a roll and cost about $5/m

Much better than $600-700 for new ones, by the time you buy the inner and outer

Attached is a pic of my old R33

You can zoom in on the front screen to what they look like

They do look different, but not out of place.

Only thing wrong with them, after about 18-24 months of being in the sun, they were showing some signs of sun damage. But at roughly$30-40 you could replace them.

post-14923-1164316318.jpg

Rear quarter window outer is bonded to the glass, buy new seal - comes with free glass attached.

Can't help with front or rear though.

Thanks mate. I sent you a PM if thats ok.

Shaun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have one and it was at ~43.5PSI.
    • Put a pressure gauge on the fuel rail.
    • I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...