Jump to content
SAU Community

Help With L24e Mod

Paul_22

By Paul_22,
in Classic & Vintage (1950's-1980's)

 Share

Recommended Posts

Paul_22 Newbie

Paul_22

Posted
  • Author
Posted
Paul22, this may interest you!

"L28 TURBO ENGINE 4 SALE - This engine was built by SWR & runs a P90 turbo head, T3 turbo, EFI manifold with 300ZX 55mm T/B, Wolf 3D ECU, FJ20 turbo injectors, electronic ignition, 125kw@w on 8psi boost & has only travelled 15,000 kms. It also comes with the electric fuel pump & swirl pot, a 2.5" exhaust system & the modified rev tacho. Engine is still in the car (260Z), can hear it run & test drive. All relevant paperwork & receipts are also available for viewing.

Price: $4500ono Location: Wollongong

Contact: Nick Email: [email protected]

Phone: 0416 283 194 (hours: 9am-9pm)".

Now, I know it's a Z engine & will reqire the sump mod which I will do if you're keen on this engine.

Ghostrider is right, this costs alot of money so be prepared to spend heaps.

Oh, & Ghostrider... 86mm/87mm pistons will go in a L24, I built one a couple of years back with triple webbers & it made 135kw@wheels, it's a daily driver & also does track work from time to time & is still going strong. However, I wouldn't do it to a turbo engine...

Nick.

Appreciate that but I am pretty keen to build my own engine and use my existing block so the numbers match. i understand that mods such as these require a lot of time and cash.

Thanks,

Paul

Ghostrider Grand Master

Ghostrider

Posted
Posted
Oh, & Ghostrider... 86mm/87mm pistons will go in a L24, I built one a couple of years back with triple webbers & it made 135kw@wheels, it's a daily driver & also does track work from time to time & is still going strong. However, I wouldn't do it to a turbo engine...

Nick.

Nick, your possibly right.

I could probably fit them into an L20A block too, but the water jackets would be a bit large.

Your quoting SWR as an engine builder? Stewart Wilkins will never recommend an over bore of 4.0mm in any L series block. The cylinder walls would be paper thin and very suspect to failure.

You might have done it, but I'm sure not going to try.

I have 2 x F54 blocks and they wont take a 3.0mm over bore, as I had them sonic tested to find out, as I was going to build an 2968 engine, but am settling for 2818 instead.

I don't know that these guys would want to be doing it either, but I suppose ANYTHING is possible if you want it enough.

Cheers, D

Ghostrider Grand Master

Ghostrider

Posted
Posted
im wondering that too, theres a few L28 (carbied) engines at my wreckers.... i can get one for $20!!!

The factory cams have codes stamped in the back end face and the L24E cam is NOT really suitable for a turbo application, but it has been used in the past.

The best off the shelf cams are L28E and will have the markings A or F stamped in the back.

The A cam came from engines origin prior to 8/81 and were in N42/N47 & P79 heads and F cams came from 9/81 onwards in P79 heads only.

Cheers, D.

the big JC Collaborator

the big JC

Posted
Posted
The factory cams have codes stamped in the back end face and the L24E cam is NOT really suitable for a turbo application, but it has been used in the past.

The best off the shelf cams are L28E and will have the markings A or F stamped in the back.

The A cam came from engines origin prior to 8/81 and were in N42/N47 & P79 heads and F cams came from 9/81 onwards in P79 heads only.

Cheers, D.

will the L28 cam go alright in a N/A l24e and what difference will it make

Ghostrider Grand Master

Ghostrider

Posted
Posted
will the L28 cam go alright in a N/A l24e and what difference will it make

Make up your mind!

You going Turbo or N/a??

Best of best off the shelf n/a cams is the one stamped C and it was in all E88 headed 260Z.

It is reputedly the Nismo works cam.

nixcars Collaborator

nixcars

Posted
Posted
Nick, your possibly right.

I could probably fit them into an L20A block too, but the water jackets would be a bit large.

Your quoting SWR as an engine builder? Stewart Wilkins will never recommend an over bore of 4.0mm in any L series block. The cylinder walls would be paper thin and very suspect to failure.

You might have done it, but I'm sure not going to try.

I have 2 x F54 blocks and they wont take a 3.0mm over bore, as I had them sonic tested to find out, as I was going to build an 2968 engine, but am settling for 2818 instead.

I don't know that these guys would want to be doing it either, but I suppose ANYTHING is possible if you want it enough.

Cheers, D

Ghostrider, I failed to clarify that the engine I built was 3mm over bore & not 4mm but have seen it done... I agree 4mm is playing with fire. In N/A trim 3mm is safe as long as the block is acceptable after sonic testing.

Paul... if you need pistons etc, I have a brand new set of 86mm with rings for $300.

Nick.

Ghostrider Grand Master

Ghostrider

Posted
Posted
Ghostrider, I failed to clarify that the engine I built was 3mm over bore & not 4mm but have seen it done... I agree 4mm is playing with fire. In N/A trim 3mm is safe as long as the block is acceptable after sonic testing.

Paul... if you need pistons etc, I have a brand new set of 86mm with rings for $300.

Nick.

Yeah! for sure.

I talk with SWR a lot and I was going to put an 87mm bore into my L20A and use sleeves, but the cost was preventative. The block would loose all of it's rigidity and it would be a mamouth task to complete and with custom liners, the bill would exceed $1500 after decking, recess grooving etc etc etc, so the F54 was obviously the better alternative.

These pistons & rings you have? Are they FLAT TOP and are the rings CHROME??

Cheers, D

nixcars Collaborator

nixcars

Posted
Posted
Yeah! for sure.

I talk with SWR a lot and I was going to put an 87mm bore into my L20A and use sleeves, but the cost was preventative. The block would loose all of it's rigidity and it would be a mamouth task to complete and with custom liners, the bill would exceed $1500 after decking, recess grooving etc etc etc, so the F54 was obviously the better alternative.

These pistons & rings you have? Are they FLAT TOP and are the rings CHROME??

Cheers, D

Pistons are dished & rings are chrome.

Nick.

nixcars Collaborator

nixcars

Posted
Posted
Yeah! for sure.

I talk with SWR a lot and I was going to put an 87mm bore into my L20A and use sleeves, but the cost was preventative. The block would loose all of it's rigidity and it would be a mamouth task to complete and with custom liners, the bill would exceed $1500 after decking, recess grooving etc etc etc, so the F54 was obviously the better alternative.

These pistons & rings you have? Are they FLAT TOP and are the rings CHROME??

Cheers, D

Just to let you know my plans, I'm building 2 N/A L28's at the moment using L14 rods. the 1st I'm using 86mm SR20DET pistons & E88 Skyline head with N42 valves (I believe it to be the best head combo to use), & the other I'm using 87mm VG30 flat tops with N42 or N47 round port.

Nick.

the big JC Collaborator

the big JC

Posted
Posted
Make up your mind!

You going Turbo or N/a??

Best of best off the shelf n/a cams is the one stamped C and it was in all E88 headed 260Z.

It is reputedly the Nismo works cam.

i am going turbo i just wanted to know if i can put the cam the engine now or should i wait till its turboed.

I will do a bit of hunting around for one of those 260z cams

Ghostrider Grand Master

Ghostrider

Posted
Posted
Yes F54 block is what you want I think.

Lots of goof info on OZDAT forums

F54's were the 280ZX Turbo block and in turbo form, never came to Australia, but some of our n/a 280's had F54 blocks in them, but as far as I know, F54 blocks never came out in 260Z's.

And JC the cam would be fine, now or later.

Cheers, D

Ghostrider Grand Master

Ghostrider

Posted
Posted

Just don't play your hand when looking for the 260 cam, not everyone knows, but I'm sure if you tell them the price will go through the roof.

The 260 cam has 256 duration and for your relative stock L24E turbo, it will probably be a little long and the L28 cam should be easier to get.

Cheers, D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • BourneToLive
      Wiring high beams in IC7 for R32 GTR

      By BourneToLive · Posted

      Hey, guys, I’m hoping I can find answer here. I have already done some searching and asking around but still nothing.    I fitted an IC7 dash in my R32 GTR, and I got everything displaying on the dash except my high beams. I get input voltage and the high beams displaying in the dash when I pull the lever, but not when I fully engage the high beams. I spliced into the Red/Blue Beam+ wire in the black center connector from the cluster, but there is also a black Beam wire I think I need to use as well. The high beams still work. It’s just a matter of getting it to display on the dash.    Has anyone fully wired in their IC7 properly ? I would appreciate any guidance on this.    IMG_8835.mov    
    • junkie
      Cleaning my wheels 😍

      By junkie · Posted

      I buy my wheel cleaner in 4 litre bottles now. Euro brakes are brutal
    • soviet_merlin
      City of Casey - This is obscene!

      By soviet_merlin · Posted

      Sounds like it may all just be some baseless outrage stoked by the carexplore guy? As in the linked social media outrage on facebook just goes back to carexplore as a source again. Further shown by the council response that nothing actually has changed: "The Private Land Use Permit has been part of the Casey Community Local Law for a number of years. It's important to clarify that this permit is not new, and no changes have been made to the permit or the Local Law in relation to the permit." The full council response in Prank's link sounds reasonable to me. Saying that as someone who neither lives there nor has a front yard to call their own  
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Clutch hydraulics are also all good, looks like a brand new slave cylinder and everything bled up well. No idea what the actual clutch is, and I don't intend to pull the box off on the floor to find out, so unless we have trouble on the dyno or at shakedown that will remain a mystery for the new owner
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Front brakes are G4 8 pot calipers over 330mm discs with braided lines. Everything looks good, pretty sure these are off my old 350. Pads are brand new and judging from gold colour are Winmax which is what I also run on my race car, Neil and I both sourced brake stuff from Matty at Racebrakes Sydney who really knows his stuff Everything has bled up nicely with all new Motul RBF600 fluid, there were 2 loose hard line connections and the calipers were new on the car so I ended up doing it 3 times but it is perfect now
×
×
  • Create New...