Jump to content
SAU Community

Recommended Posts

hey guys,

curious as to know weather or not most people remove all accessories (ie intake manifold and turbo) from the head before pulling it off? had a bit of a search and turned up nothing :laugh:

cheers,

mark.

it depends on if you can access the two little 10 mm bolts hiden at 7 oclock and 1 oclock if your standing in front of the car, looking at the motor. i cant remember, but there hidden. especially the front one.

take the turbo off, but may aswell leave the manifolds on, they make good handles when lifting it off, however the intake manifold adds heaps of weight.

and yea there are a couple of 10mm bolts "hidden" on the outside, as opposed to the "inside" where the head studs are

thanks for the advice so far guys, keep it coming :laugh:

by hidden 10m bolts do you mean under the cam cover? Haven't got this far into it yet, i've just got all of the intake piping detatched and fuel lines disconnected heat shields off and have removed the cam covers to make sure i have the right sized socket/allen key to undo the head studs.. now i'm working on unbolting the dump pipe from the joint just before the cat, f**king tight up these bolts are :D

take the turbo off, but may aswell leave the manifolds on, they make good handles when lifting it off, however the intake manifold adds heaps of weight.

and yea there are a couple of 10mm bolts "hidden" on the outside, as opposed to the "inside" where the head studs are

and by 10mm bolts do you guys mean the m6(10mm head) bolts of which there are 3 not 4. two at the back and 1 at the front i believe.

Youve just undone the headstuds and removed everything in sight, and the bitch still wont come off...then your 13 yr old brother handing you spanners says...it wouldnt be those m6 bolts holding the head down would it? haha...ohh funny but frustrating times.....

hha yeah 3 of them, need to remove the cam gears to get to the front one easily.

even worse on teh rb30e's, cant figure out how they even got the bolt in teh hole at the front lol

i use a engine crane, even with the head only, so manifolds stay on.

ah i look forward to it all tomorrow arvo when i finish work.. i got the shits with it tonight and ran out of light, decided to take the turbo then the exhaust manifold off.. i will put dads new rattle gun to good use tomorrow :(

ah i look forward to it all tomorrow arvo when i finish work.. i got the shits with it tonight and ran out of light, decided to take the turbo then the exhaust manifold off.. i will put dads new rattle gun to good use tomorrow :(

shouldnt need a ratlle gun for any of the bolts on the motor

jesus christ..

turbo is off, top half of intake manifold is off.. EVERY SCREW IN SIGHT IS OFF but the bitch still won't move! please.. help!

did you get the 3x 10mm head bolts off?

front one is behind the inlet cam gear

far out.. behind the inlet cam gear, sorry to be causing such a bother but how the hell does one get that off? it doesn't look like it's bolted on like the exhaust cam, or if it is the bolts are underneath the VCT cover bit on the actual gear.. i removed 3 out of the 4 bolts on that to check out if there was a spring underneath and indeed there was so that went back together pretty quickly.. any suggestions?

did you get the 3x 10mm head bolts off?

front one is behind the inlet cam gear

sounds like you need a bigger hammer..

recheck all the head studs and make sure you have all the little bolts out. theres nothing else except the headgasket holding it on.

All else fails hook your block and tackle up to the head and keep lifting until the front wheels just leave the ground then start smacking it with a hammer or 2 x 4!

works every time.

haha i like your style but i think i'll save it as a last resort :) now i know theres another bolt behind the intake cam it's just a matter of getting it off, and i now realise that there's also one behind the exhaust cam.. they're located pretty high on the head though so i'm not convinced that these are actually holding the block on.. how strong is the seal between the headgasket block and head?

sounds like you need a bigger hammer..

recheck all the head studs and make sure you have all the little bolts out. theres nothing else except the headgasket holding it on.

All else fails hook your block and tackle up to the head and keep lifting until the front wheels just leave the ground then start smacking it with a hammer or 2 x 4!

works every time.

far out.. behind the inlet cam gear, sorry to be causing such a bother but how the hell does one get that off? it doesn't look like it's bolted on like the exhaust cam, or if it is the bolts are underneath the VCT cover bit on the actual gear.. i removed 3 out of the 4 bolts on that to check out if there was a spring underneath and indeed there was so that went back together pretty quickly.. any suggestions?

you will need to remove the inlet cam gear, yes there is a spring behind it.

i made some pics for you

post-5157-1164636664.jpg

post-5157-1164636674.jpg

post-5157-1164636694.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just something I found searching for more info on Emotion R, apparently the ECR33 Skyline GTS25t was either originally black, or there were two of them, the black one being the original demo car, then building a white one which was part of the 1997-onwards (to at least 2008!) Cockpit Tatebayashi Tokyo Auto Salon booth demo cars. It appears that Emotion R closed down in 2008 and was declared bankrupt in 2010: http://bank-db.com/hasan/208365. Scan of a magazine with the black R33 from 1996: Wayback machine archived page from May, 2000: https://web.archive.org/web/20000529061027/http://www.emotion-r.co.jp/skyline.html Option magazine with a few photos from the Cockpit Tatebayashi booth at the Auto Salon from various years: 2002: http://www.jdm-option.com/photo/index.php?action=item&category_id=154&image_id=3507 2003: http://www.jdm-option.com/photo/index.php?action=item&category_id=137&image_id=3033 2005: http://www.jdm-option.com/photo/index.php?action=item&category_id=116&image_id=1831 In 2008 Cusco website mentions that the Cockpit Tatebayashi ECR33 was displayed at that year's Tokyo Auto Salon: https://www.cusco.co.jp/event/2008/12/post_735.html As of 2021 it appears that the ECR33 demo car ended up being exported to Florida, USA: https://rmcmiami.com/inventory/1996-nissan-skyline-r33-cockpit-tatebayashi-demo-car-big-te06-turbo-endless-brakes-lsd-450hp/ And finally here's Google streetview of the Emorion R garage in 2023 which is amazingly not only still there, but the showroom is still full of various parts in stock and funishings, etc.: https://maps.app.goo.gl/ttyEAZdZLyzermyT9 Apologies for nerding out a bit. I used to love doing this 20 years ago on SAU and got a bit nostalgic for a moment... 馃槄
    • Try fabricating something like this and install it under the pedals? Not sure if it's legal or not....
    • Even though I have some pretty good (brand) ratchet ringies, I avoid using them to break open tight bolts. A broken ratchet is very annoying.
    • Also, there's always room for 4 or 5 3/8" drive wobble extensions of various lengths so you can operate the ratchet from a better location.
  • Create New...