Jump to content
SAU Community

Recommended Posts

Hey all never thought about this and if its possible, but im thinking of flying over east next week to buy a car, and was actually thinking while im at it, drive the car back to perth myself and make it a road trip instead of getting it shipped here, would cost me the same with fuel i know but would be more itneresting. anyway.....

My question is...is there any way to disable a turbo on an r34? maybe pull some boost hose out or sumthing? seems abit useless for the turbo to be constantly spooling on a 3000km journey.

Any ideas?

cheers

Edited by supraaah
Link to comment
https://www.sau.com.au/forums/topic/144505-is-it-possible-to-disable-a-turbo/
Share on other sites

cruising it will probably not even be making positive pressure, it will be fine.

the way to 'disable' it would be to wire open the wastegate.

well lets just say im in 5th gear and not quite doing the speed limit, it would be spooling up abit wouldnt it? i mean the nallabor plain is a long road my foot might accidently get stuck on the accelerator.

any idea where the wastegate is? and if that would be a viable option?

BTW- i have an external wastegate on my supra (50mm chinese HKS copy) which has seized open, and my turbo still spools up, so wouldnt that be the same principal ur on about? in which case turbo still spools.

Edited by supraaah
well lets just say im in 5th gear and not quite doing the speed limit, it would be spooling up abit wouldnt it? i mean the nallabor plain is a long road my foot might accidently get stuck on the accelerator.

any idea where the wastegate is? and if that would be a viable option?

BTW- i have an external wastegate on my supra (50mm chinese HKS copy) which has seized open, and my turbo still spools up, so wouldnt that be the same principal ur on about? in which case turbo still spools.

if your wastegate is seized open how are you getting boost ? dont they vent excess boost ? meaning if its open before you reach set boost level it wont go anywhere

you would use more fuel by "Disabling" the turbo for your trip than you would using the thing.. and even if your cruising along at 160kph you shouldnt be seeing much boost to maintain a cetain speed if any at all

remember.. if you disable your turbo it will be a gutless bucket of junk to drive!!!

Edited by rb26s13
You're nuts mate. If you don't want a functioning turbo don't buy a turbo car. If you do buy one just drive it. That's what they were built for.

I second this. Drive the thing, you will soon find it doesn't just boost when on steady state cruise.

Best way to disable a turbo? Tip a handful of shotgun pellets down the air intake. Guaranteed to work :laugh:

I agree with the majority of opinion here - on cruise, the turbos are simply "spinning in the breeze" - you should find that the engine is still under vacuum.

If you disable the turbos, and you find yourself in a "sutuation" (eg misjudged how much time/distance you have to overtake a B-double), then you won't have the turbos to assist you in your time of need.

Just leave the damn things alone.

i would have to agree, on the simple fact that you are driving across a desert in a car that you aren't familiar with. you don't know if the thermostat or clutch fan is working properly. so you run the risk of cooking it on the way. at 100kmh there would be plenty of air going through the radiator, but it could still get rather hot. and if something breaks you could be stuck in the middle of nowhere.

to those of u with helpfull and productive comments ...thanks, to the rest of u no one asked u to comment if u dont agree, notice i said "just an idea" i own a supra (hence my avatar) with different turbo setup and different gear/diff ratios, doing 160 even in sixed my turbo is spooling up quite abit, now as a newbie to the r34 i have never driven one, im buying it on my brothers behalf. Once again, thanks to those with productive comments :)

dont be so one sighted, there are different caars out there, if an r34 wont be spooling up at that speed, doesnt mean others wont...thats why i asked

no car would spool up at light cruise at 100km/h

even at 130kmh. the turbo has no relationship to road speed

it only cares about exhaust gas, which is derived from engine load

load the engine up, and it will wind up

the turbo will only spool if you open the throttle

engine load makes exhaust gas, exhaust gas makes the turbine spin

so once more

no car will make boost unless you pull the throttle cable enough

it wont under any circumstances staring winding in 12psi if you are just light crusing along the highway

supraaah - serious answer is that you will not be boosting at all infact you will have negative boost ie. vacuum. at cruise - which is most of the time so you will be just fine in the fuel economy department.

Also there is very little increase in fuel consumption and a lot more efficiency to be had from using the turbo when you are accelerating.

If you are wanting fuel economy what counts is how long you can maintain a cruising speed vs accelerating time. So if you drive in a way that you brake less and therefore don't have to accelerate back up to speed you will get more fuel economy. Accelerating hard onto the freeway will not see you use more fuel! What you will get is better power to weight ratio output from your lighter engine which has a turbo instead of a larger and heavier engine.

Once you drive it, check out the boost guage, this will show the boost negative or positive. Its definately extremely negative when you are cruising.

Do try to drive when accelerating with the rpm in the powerband where your engine is most efficient ie.over 2200rpm.

Don't forget the energy is used to get you up to speed and lost in braking. How hard you accelerate so long as you aren't going to brake for a while especially makes almost no difference to the fuel economy.

So feel free to use that boost to get you up to speed but try to maintain the speed without having to brake. If that means driving slower to make it through all the lights in the city without braking or coming up to a lower speed so when you do brake you don't lose as much energy from your last acceleration thats the way to go for fuel economy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah. air pressure leakdown test is where I would be headed next here, using one's ears to determine whether it's the valves or bores/rings leaking...
    • More likely you didn't bed the rings in correctly and have glazed the bores. Running with misfires on a fresh build is somewhat of a no-no. Surely no-one "smoke tests" the combustion chamber? That's what a leakdown test is for. Smoke testing is, um, a bit of a wank at best, and only really useful for external pipework.  
    • Well, obviously that kit is not a relocation kit or anything other than just the original isolators and the like. I would suggest that it should be a matter of just bending up some flat bar to build a mount over the top of some other diff, with the flat bar held to the back of the diff by the rear hat bolts. A little welding, a little thinking about how to secure the front of this structure, maybe some different hoses in case you can't get it in just the right place.
    • Pay diff/trans workshop to do this.   Nope. Z32 turbo ran R230 with 6 bolt GTR style axles. All other Z32 were R200. Basically same same as other R32 stuff. All were a viscous waste of space.
    • So, I'm not a diff swapsies specialist, but I am pretty sure the 300zx ran an R220 not and R200 like the C34 Stagea, so I think it is of no use to you. As you said, all you need to do is get the centre swapped in the diff you have, which might be best done by a diff specialist. The current centre is probably desirable to someone to track so an easy path might be to swap your mechanical centre for someone with a standard centre (which is a viscous LSD, and almost certainly won't have any limited left). The only thing you have to watch swapping R200 internals between diffs is that the number of splines on your car's stub axles has to match the donor car, or you need the centre+stub axles and make sure they have the same number and pattern of bolt holes as your rear axles.  You swap your current ratio onto the new centre so you don't have to worry about matching the front. Alternatively, centres like the Nismo pro are much gentler (and have adjustable "tightness") so you could buy on of those from somewhere like Jesse Streeter or Nengun (noting it may cost you 1234% extra in tariffs by the time it lands)
×
×
  • Create New...