Jump to content
SAU Community

Need Help?

cheez

By cheez,
in Engines & Forced Induction

 Share

Recommended Posts

cheez Mentor

cheez

Posted
Posted (edited)

hey guys,

wat is this pipe connected too and what is it for?

it was connected to the standard intercooler pipe, as shown, and the other photo shows where it is in the engine. am stuck atm with the install of the cooler,

please note that the black pipe shown by itself, is the standard cooler pipe. it has a connection point circled, and that is where the small pipe in the other pic connects to

need help

wanna finish install tonite

cheers

daniel

post-31466-1164366538.jpg

post-31466-1164366551.jpg

post-31466-1164366573.jpg

Edited by cheez
Link to comment
https://www.sau.com.au/forums/topic/144648-need-help/
Share on other sites
steveo_r33 Proficient

steveo_r33

Posted
Posted

i just did a cooler install..

the nipple on the pipe is what runs off the boost solenoid or something ...

fact is i dont really know where it ends but i know that running your car without that vacuum hose being run back into the cooler piping your engine will run unlimited boost and basically..

BOOM

I simply went to ricol and got a nipple put into my cooler piping.. hooked it up and kicked her over..

cost me 20 bucks

ricol is in sydney / peakhurst dno where ur at

Link to comment
https://www.sau.com.au/forums/topic/144648-need-help/#findComment-2702481
Share on other sites
steveo_r33 Proficient

steveo_r33

Posted
Posted

u cant finish install tonight unless you want to ruin your engine... if you plant it that is... just go get one of those nipples from a hardware store or something tomoro and weld it on or make a thread in the pipe.. seal it with plumbers tape and off you go...

Happy Modifying..

Link to comment
https://www.sau.com.au/forums/topic/144648-need-help/#findComment-2702484
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Ball bearing turbos

      By sunsetR33 · Posted

      Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Lithium
      Forced Performance Hta Turbos

      By Lithium · Posted

      Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...