Jump to content
SAU Community

Recommended Posts

bad bad bad!!

is it from the radiator? or from the block?? If it is from the block it could be a busted head gasket and its going to cost big $$$ If you continue to drive it you will warp or crack the head resulting in even bigger $$$

If you are lucky.. it is just busted radiator, or split radiator hose. Not that you should be driving it in this condition, but pop the bonnet.. you should see steam shooting out from somewhere - which will narrow it down. If you are lucky it will just be a hose.

My recommendation is not to drive the car at all until you can work out the problem. It most likely is quite serious.

Temperature problems can be FATAL to an engine..especially a modern engine.

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296076
Share on other sites

got your PM pred and thankyou for your help... damn, now im shitting my pants, don't know where exactly it is leaking.. i looked under the car and it has the black shield covering under it so i couldn't tell whether it is the hose, or the block but it is defintely 100% coolant(green liquid). Just went down to the local mobil petrol station and brought some radiator stop leak treatment bottle.. going to add it and hope it helps.. :D:(

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296330
Share on other sites

Guest RedLineGTR

Check the hoses, or remove the cover. Just follow the hoses down to where they end like the bottom one see if there is any fluid leaking. Best Bet is jack it up and take the cover off. I could be the water pump (how many k's) some of them go early before 100k. Or could be a cracked radiator as suggested above. (which is alot less common).

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296580
Share on other sites

I'll put money on it being your water pump. Check the water pump, there is an inspection hole that will allow coolant to slowly leak when the pump seals shit themselves (telling you it's time to replace the pump). With the undertray in place you'll never be able to pin-point the source of the leak. The tray comes off easily.

If the pump is the cause you're up for a new one, & you may as well replace the timing belt while you're there. You need to take the same bits off - so why do it twice?

New pump from Nissan (same as RB30 VL pump) - $90-100

Timing belt - $80-90

Labour - ~$150 (dunno' exactly on this one?)

I very much doubt it'll be a major problem, so don't stress too much :)

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296690
Share on other sites

Originally posted by pushead

I topped up the coolant in the white bottle as well as the alternator last night

Alternator - coolant? WTF! Coolant & the alternator don't mix well dude!

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296695
Share on other sites

Originally posted by whatsisname

Alternator - coolant? WTF!  Coolant & the alternator don't mix well dude!

???? so you put water instead of coolant in the alternator? i followed a black hose which goes to a white bottle(the backup bottle) which labels coolant.

Checkout the attached Picture:

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-296768
Share on other sites

you lucky bastard :D with the temp that hot ur lucky nothing blew

mine ran hot once and blew the seals on the plastic radiator end tanks - goodbye radiator

the water pump is a c*** to get off cos of the crank pulley bolt. you will more than likely need a rattle gun to get this off

the water pump may not be dead, it my just be the seal, in which case pull the pump off, put new sealant around it (doesnt use a gasket) and put it back together

you can drive around with a leak BUT make sure u keep the system topped up

if it starts sucking air or depressurises it will overheat again and u may not be so lucky

take it to a mechanic and there are pressure tests you can do on the radiator so check for a leak/crack. you can also run a test to see if there are exh gases in the system (leaking head gasket) so you will be able to pin-point the problem

just finally, cooling systems are ****s to work on and fix, if youre going to repair it make sure u do it right cos its the kind of thing which if not done properly will cause alot of headaches

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-303732
Share on other sites

Originally posted by whatsisname

I'll put money on it being your water pump.

New pump from Nissan (same as RB30 VL pump) - $90-100

Timing belt - $80-90

Labour - ~$150 (dunno' exactly on this one?)

I would say this is invaluable advice.

Our pumps are cheap which is good.

You want to do pump, timing and accessories belts at once to save labour.

$150 for labour is damn cheap though.

T.

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-304054
Share on other sites

I paid $350ish (think it was 350? Certainly under 400) for a new genuine Nissan w/pump & timing belt. Both installed. Thanks Vince (Rigoli).

I didn't want to take any chances so I got them both done. That way I knew they were new :)

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-306926
Share on other sites

Originally posted by whatsisname

I'll put money on it being your water pump. Check the water pump, there is an inspection hole that will allow coolant to slowly leak when the pump seals shit themselves (telling you it's time to replace the pump). With the undertray in place you'll never be able to pin-point the source of the leak. The tray comes off easily.  

If the pump is the cause you're up for a new one, & you may as well replace the timing belt while you're there. You need to take the same bits off - so why do it twice?    

New pump from Nissan (same as RB30 VL pump) - $90-100

Timing belt - $80-90

Labour - ~$150 (dunno' exactly on this one?)

I very much doubt it'll be a major problem, so don't stress too much :P

Thanks for your detailed info dude.. really needed it...yep. same as the RB30 VL pump.. what hole are you refering to which you can tell the water pump shit itself?.. i couldn't seem to find it.. is it near the fan belt?

Link to comment
https://www.sau.com.au/forums/topic/14512-tempreture-is-hot/#findComment-310998
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...