Jump to content
SAU Community

1982 Nissan/datsun 280zx

Archie@

By Archie@,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

Archie@ Experienced

Archie@

Posted
Posted

Hi all, it's been a fair while since I've been on here or for that matter anywhere near my car. Basically wanting to sell it as I work long hours so I simply don't have the time and energy for the attention it needs.

It does need a little TLC, nothing too serious. It has had the cylinder head replaced about 6-7 months ago and it hasn't been driven since i got it home so I definitely will need the head re-tensioned and that's why it's blowing just a little bit of blue smoke.

Apart from that it runs pretty good. I haven’t fired it up in about a month so I'd say the battery is probably gone flat.

Other little problems are a small dent in the drivers side door, and someone ran up my arse and so the right rear light is cracked and a little dented, but nothing too serious and not really all that noticeable. Apart from that the car is pretty much immaculate.

Have a full service and rego history spanning something like 10 years or more (I'll have to dig that out, I know it's somewhere in the living room :) .

It's got roughly off the top of my head about 250K on the clock (but I'll confirm the exact K's when I get home tonight).

It's Silver/black two tone. It's a series 2 but has series 1 rims. Happy to email pics to anyone, just email me.

Rego is until the later half of January 07.

I'm looking for $2K flat. The car is in Neutral Bay in Sydney.

I'm contactable on either 0400036014

or [email protected]

or [email protected]

If you are interested, please remember the car isn't running too crash hot due to it needing the cylinder head retightened so the best bet is to either drive it to a mechanic that’s close by (I can recommend a few good ones in the area, or have a tow truck).

Oh and it has been garage the entire time that I’ve owned it, and judging by the condition it was garaged for most if not all it’s life.

Any questions, feel free to contact me.

Link to comment
https://www.sau.com.au/forums/topic/145374-1982-nissandatsun-280zx/
Share on other sites
  • 2 weeks later...
Archie@ Experienced

Archie@

Posted
  • Author
Posted

I'll try and get some better and more curent shots up over the weekend, these are the ones i have at work.

Sorry about the latness of the pics flip.

blk180, email sent.

post-13320-1166159197.jpg

post-13320-1166159242.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      Rb26 iron block limit

      By r32-25t · Posted

      You don’t need to use full throttle all the time to break these blocks, 500kw at the wheels in more then enough to break them even with an occasional squirt. Hell I’ve seen them break under 400kw
    • Dose Pipe Sutututu
      Question about BoV on RB25DET NEO

      By Dose Pipe Sutututu · Posted

      A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Predator1
      Rb26 iron block limit

      By Predator1 · Posted

      Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • Roy
      Rb25/30 Rb30det Vvt Internal Oil Control

      By Roy · Posted

      So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Kapr
      Question about BoV on RB25DET NEO

      By Kapr · Posted

      Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
×
×
  • Create New...