Jump to content
SAU Community

Recommended Posts

Hard luck dude the odds caught up.

May i ask whats wrong with your exhaust and wheels setup?? Or why they defected?

They're 18" and stock are 16" so i'm right, but i need engineer certificates saying that they comply with the australia design rule.

same with exhuast... any modified exhaust on a car has this rule

Yeah really, it'll cost you more grief than its worth. Lesson learned

definitely

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Dude ouch!!

As said, yes it could of been a lot worse.

Sucks though majorly that you got done though; for both speeding and defects.

What a shit way to start Christmas

I had the same treatment not long ago... sent to epa for noise... had to whack a stocker pee shooter on there to pass... and the dicks defected me for an unenclosed pod filter.... and ride height..

but i out smarted them with the ride height ... i just put tighter rubber things on to support my exhaust and it raised it like 30 mm .. lool

They're 18" and stock are 16" so i'm right, but i need engineer certificates saying that they comply with the australia design rule.

same with exhuast... any modified exhaust on a car has this rule

definitely

Hey,

no, don't think so. Pretty sure exhausts are an 'owner-approvable' modification according to the RTA.

This means that as long as it passes the relevant ADRs (ADR28, for noise level; ADR37, for actual

gas and particulates; there may be others - ask the RTA) it's OK. It doesn't need to be standard.

What most likely happened is that they tested your car with a dB meter; and it was too loud (corrected

reading of over 90dB, putting the car in violation of ADR28). I doubt they tested ADR37 - pretty sure

the kit to do that test only exists at Penrith and Botany.

To fix this, visit an exhaust shop with a meter and tell them you need it quieter than 90dB at test RPM -

for you, it's probably around 3500RPM. Note I said 'corrected' - they're supposed to apply corrections

for temperature and pressure (this doesn't often happen). If you get tested in the middle of a cold night

your car will read louder than in the middle of a hot day.

Borrow a set of stock rims.

Then visit the inspection station, show them your car complies with the paperwork, and get the

defects cleared. Visit them in the middle of a hot day in case they don't apply the corrections on the

noise test.

Then your car is street-legal again, and you can figure out whether you want to get your car

engineered (budget about $500) for the rims or not. If the rims stick out beyond the bodywork I'd

guess you have SFA chance of getting them approved - talk to your engineer about that (you might

be able to flare the guards enough to get them allowed). Might be better to replace them with a set of

smaller rims which don't require approval from a signatory.

Lastly, don't drive like a tool. Driving like a tool attracts the wrong sort of attention. And if you _do_

drive like a tool, don't be surprised when the police throw the book at you.

Regards,

Saliya

Hey,

no, don't think so. Pretty sure exhausts are an 'owner-approvable' modification according to the RTA.

This means that as long as it passes the relevant ADRs (ADR28, for noise level; ADR37, for actual

gas and particulates; there may be others - ask the RTA) it's OK. It doesn't need to be standard.

What most likely happened is that they tested your car with a dB meter; and it was too loud (corrected

reading of over 90dB, putting the car in violation of ADR28). I doubt they tested ADR37 - pretty sure

the kit to do that test only exists at Penrith and Botany.

To fix this, visit an exhaust shop with a meter and tell them you need it quieter than 90dB at test RPM -

for you, it's probably around 3500RPM. Note I said 'corrected' - they're supposed to apply corrections

for temperature and pressure (this doesn't often happen). If you get tested in the middle of a cold night

your car will read louder than in the middle of a hot day.

Borrow a set of stock rims.

Then visit the inspection station, show them your car complies with the paperwork, and get the

defects cleared. Visit them in the middle of a hot day in case they don't apply the corrections on the

noise test.

Then your car is street-legal again, and you can figure out whether you want to get your car

engineered (budget about $500) for the rims or not. If the rims stick out beyond the bodywork I'd

guess you have SFA chance of getting them approved - talk to your engineer about that (you might

be able to flare the guards enough to get them allowed). Might be better to replace them with a set of

smaller rims which don't require approval from a signatory.

Lastly, don't drive like a tool. Driving like a tool attracts the wrong sort of attention. And if you _do_

drive like a tool, don't be surprised when the police throw the book at you.

Regards,

Saliya

Wow, thanks for that.. I can tell you now that my exhaust has been already defected and taken to an exhaust shop which complies and is under the 90db rating. RTA did NOT use any sort of meter for the exhaust as the car was off, For the rims, i'm putting stock back on and getting cleared..

Thanks for all your help.!

bad luck matey, the defect doesnt look too bad though couldve been heaps worse. shouldnt be too difficult to get it cleared

if the cop really wanted to be a c**t he wouldnt of let you chuck a shit lol.

good luck with the defect clearing.. looking at the bright side, at least with the 3 months you have off you'll save alot of money not driving and modding :)

Just a quick note, you won't lose your license for ages yet. I know someone who was booked for the same offence in January of this year. He paid the fine on time and received the letter from the RTA a good few weeks later advising that his loss of licence was to occur in the first week of May through to July.

that defect notice they gave you specifies that to be cleared you need to get a minor part inspection at an AUVIS.

This means that you only need to get it inspected at any place that can provide a blue slip.

Put the parts that were mentioned on the notice back to standard, then get it inspected. You may not even have to change the exhaust, talk to the place you are going to get it passed by and see what they say needs to be changed before doing anything.

Either way, you don't need to take it for a full RTA inspection and emissions test, so dont stress about it, it is not big deal.

You will probably still have your license for a while yet, so get it done now while you can drive.

Sorry to see you got caught out!

Edited by siksII
wow intresting...

D_I_F i had mcdonalds.. i have no idea how i got sick..

Sorry dude but I suffer from the same problems.. if I eat something wrong it def wont agree with me.. so I stop eating those kinda foods.. Sloves the problem all together..

Not to mention you just got your licence and should know better..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
    • I have a r34 sedan 1999 manual converted need some help with my speedometer it only reads upto 98km and then stops currently still running the auto cluster any easy fixes no speedo drive is connected yet, if someone has a video for wiring up the manual speedo sensor with the auto cluster please send through 
×
×
  • Create New...