Jump to content
SAU Community

Recommended Posts

The boot on my R33 is jammed shut. The boot release lever at the side of the driver's seat doesn't have the normal pressure when i pull it, and although i hear a faint sound when i press the boot release button on my alarm system, the boot doesn't unlock.

I've tried pulling up the boot with the lever up but it doesn't work.. i suspect it's the locking mechanism or boot which is jammed or something.. and it probably happened a few days ago when my friend slammed the boot shut =_=

It's kinda hard to describe, but the left hand side of the boot is slightly open, but the right hand side of the boot is closed (I an tell by looking at the gap between the body and the boot), so the boot is actually closed at a slight angle.

The lock on the boot is broken too, so I can't use the key to open it.

Is there any way which I can get it to open again? I've thought of removing the back seats to access the lock from the inside, but how do I do that, and will it help?

Link to comment
https://www.sau.com.au/forums/topic/146509-r33-boot-stuck-shut/
Share on other sites

Nah... unless you can reach through the speaker holes, you can't get through to the boot like that.

It shouldn't half open unless something is jamming the arms that the boot swivels on. There is only one latch that holds it shut.

As for the loose handle, it's possible that the wire has come loose... If you have a look under the carpet, you should see how to adjust it. (or pull it with a pair of pliers until the boot opens)

Carpet... carefully pry one side of the skyline door-sill up, then move your hands across, and unclip the next etc etc. From there, you can unhook the side of the carpet and have a better look at the mechanism.

I've heard of people drilling the lock out and replacing it when they were stuffed. I guess you really don't want to do that, so check the cable tension first. =-]

Worst comes to worst, if you need to get into the boot to fix the lock, you can remove the back seat, then remoev the boot inspection panel. There is a lot of stuff in the way, but that can be unbolted from the cabin and moved.

you might not be able to crawl through the hole, but a small kid can.

The hole is sharp though.

Sounds like something is jammed on one side of the boot, causing excessive pressure on the lock, which can prevent the release mechanism from releasing.

Gently apply downward pressure on the lifted side, then press the boot release button on your remote and try to lift your hand quickly. Timing is the key. You can also get someone to hold the lever up, while you push down on the boot and then release it (boot lid).

Sounds like something is jammed on one side of the boot, causing excessive pressure on the lock, which can prevent the release mechanism from releasing.

Gently apply downward pressure on the lifted side, then press the boot release button on your remote and try to lift your hand quickly. Timing is the key. You can also get someone to hold the lever up, while you push down on the boot and then release it (boot lid).

Doesn't work :stupid:

I got someone to hold the lever up while i pressed down on the lifted side.. the car went down but the boot didn't, and it's still stuck.

Maybe i should get a locksmith to open it...

You haven't mentioned anywhere that you've tried the key? Unless I missed that somewhere.

If the wire is loose, and the lock won't open because of it, then the key will over-ride that anyway.

Yea, you missed it ^_^

The key doesn't fit the lock, so i can't use it.

Doesn't work :P

I got someone to hold the lever up while i pressed down on the lifted side.. the car went down but the boot didn't, and it's still stuck.

Maybe i should get a locksmith to open it...

Did you get it?

Did you try the boot release button on your remote while your pushing on the boot lid like Al said?

I agree with Al about pressure on the latching mechanism.

Maybe if you dress up an act just like the Fonz and just give the boot a hit it'll open..... hahahah sorry, jokes man :D

edit: spelling

Edited by KeyMakeR33
Worst comes to worst, if you need to get into the boot to fix the lock, you can remove the back seat, then remoev the boot inspection panel. There is a lot of stuff in the way, but that can be unbolted from the cabin and moved.

you might not be able to crawl through the hole, but a small kid can.

The hole is sharp though.

thats the easiest way to do it, to remove the rear seat takes 4-5 mins max, then there is a dozen or so 10mm bolts and your into the boot , on once in manually open the boot from the inside , then once u have it open diagnose the issue.

if there is no pressure on the lever in the cabin, it may also be snapped the cable

There is a 'valet' switch that disables the remote release. It's possible that something in the boot has accidentally knocked it to the 'valet' position.

If your key lock is broken, you may need to get a locksmith (as mentioned previously) to break in for you.

Any reason why one side of the boot was higher than the other?

No idea. That side is still like 1/3 a cm higher than the other.. but it still opens, so i'm not really concerned about it. It doesn't look like rain will go in too, so it's okay.

I thought something was stuck too, until today.

I'd guess that the rubber stoppers are taller on one side than the other? The bonnet rubbers are adjustable by winding them in and out, but I didn't think the boot ones were?

Well, if the cable was loose, than my manual method should have worked! (pulling up the side of the carpet, disconnecting the cable, then pulling on it by hand... or ajusting the cable tension)

if there is something that could possibly be putting pressure on the boot, i'd go for a quick lap around the block doing some hard stopping and swerving to see if that helps.

Dude! That's a sweet idea! I'm going to try this right now! (I don't have any issues with my boot though?) =-]

Still, that's a great idea for anyone who got something stuck under the boot-arm. I used to get PC's stuck under mine, and you can't shift them over with a coat-hanger!

  • 2 weeks later...

25th December 2006 @ 14.30

Whilst cleanin the boot out i manage to play with a metal plate inside the boot lid. (not knowing it was the valet switch)

19.30 Whilst travelling down Pitt St in Sydney I managed to get a samell metal fragment in my tyre. (resulting in a flat tyre)

19.31 I realised the boot was not releasing from the boot leaver inside the cabin. No tension at all behind the leaver. Just free air when u pull it up.

19.32 I decided to try the boor lock. It didnt work. The lock is broken. It keeps on making a ticking sound but nothing happens.

19.32: 15 ...I start to swear.

19.34 I try other methods...no good. So I baby it all the way back to Liverpool.

21:00 got home in one piece.

26/12/2006 @01:46 I read this thread and I will try the boot cable under the carpet 1st. So how I go tomorrow to get to the spare.

Why is that Valwt switched linked to the leaver....or is that the safety feature of it or am I totally worng and it is only coincidence???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
×
×
  • Create New...