Jump to content
SAU Community

Recommended Posts

East Bear will definately be pricey,.. but it's going to fit alot better than a cheaper alternative.

Wayne J; I know how it is being in two minds about LED tail lights, I've definately considered it, ... the stock ones do look a bit dated, but they will always look tough as,... whereas the LED's just look "pretty". :banana:

East Bear will definately be pricey,.. but it's going to fit alot better than a cheaper alternative.

Wayne J; I know how it is being in two minds about LED tail lights, I've definately considered it, ... the stock ones do look a bit dated, but they will always look tough as,... whereas the LED's just look "pretty". :)

True. Sometimes they're a little too "bling" for me, certain ones anyway.

My stock tailight lenses look a little dull/faded, as do the (rather useless) reversing lights.

I have some plastic polish and might try to revive them a little when I get the time.

Hey that reminds me - I've noticed that some 34's seem to have one reverse light clear and the other is red (or has a red globe)??? What's that about, anyone know?

Here's a perfect example:

Rear.sized.jpg

Cheers,

GTR's are ALL like that with the reversing light and the fog light.

Also, SOME GTTs had that,including mine, but I'm the only GTT I know that had this option. I think it was included in the "snow" kit on mountain cars which also includes heated side mirrors and heated windscreen wiper pads to keep the wipers from freezing onto the windows.

:)

GTR's are ALL like that with the reversing light and the fog light.

Also, SOME GTTs had that,including mine, but I'm the only GTT I know that had this option. I think it was included in the "snow" kit on mountain cars which also includes heated side mirrors and heated windscreen wiper pads to keep the wipers from freezing onto the windows.

:laugh:

Thanks Bass Junky for the explanation! :P

the fog light i remember someone saying a while ago was an optional for the GT-Ts.

Sheng/q looks good :( rims are a bit small though.

a cold day or something? Everyone in the background has their arms crossed.

My stock tailight lenses look a little dull/faded, as do the (rather useless) reversing lights.

I have some plastic polish and might try to revive them a little when I get the time.

I have one discoloured reverse light.

When I purchased my car, the only other GT-T in the lot had the same light (left hand side) discoloured, so I wondered if it was a common fault as in not sealed properly. It's quite annoying, however I havn't had the guts to do the whole baking in the oven, polishing, and resealing thing yet,.... I'm a newbie when it comes to DIY. I dread when the time comes where I'll have to polish up the headlights.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...