Jump to content
SAU Community

Recommended Posts

Ok so my alternator isn't working properly (when i have lights on or use brakes with stereo my power steering jolts and my Hicas light blinks, have tried a new battery, no help, battery diagnosing thingo at beaurepaires put it down to alternator) and i don't know what to do.

Should i replace it with a second hand one (if so where do u find these?? Jap wreckers only seem to stock engine and performance parts) Should i get one off another model car (r31 or something?) should i buy an aftermarket one? Should i get one from Nissan ($400ish i think) or get my current one rebuilt ($400ish?)

Also can it be just a cheap part of the alternator causing my problem?

Thx

Link to comment
https://www.sau.com.au/forums/topic/147179-alternator-where-how-much/
Share on other sites

Before doing all that, take the leads off the alternator and give them a good cleaning, it might just be something as simple as dirty contacts stopping a full charge getting through.

Seriously, get a hammer and hit it, and it will probably keep working for a fair while. Sounds very Datsun styles, but it actually works well.

LOL I had a Bluebird with the same problem, always had something in the boot to wack it with :O

If u decide not to rebuild give Dean a buzz @ UPI 9555 3611 im sure hed have a few lying around.

Ohh ok thanks guys, rebuild for $300 doesn't sound bad... Didn't think of cleaning the contacts, i'll try cleaning those and err wacking it with something (my favorite automotive fix.. something i actually know how to do) then if that doesn't help i'll ring the places above.

I would take it to an auto electrician but 2 that i've been to, seem to think it has nothing to do with the alternator (regardless of voltage drops and such) and say my power steering is just shagged, so i'm assuming they don't do imports. I'll post back here with what i ended up doing and the prices, might be helpful to someone else

If you pull the alternator appart yourself and take it somewhere they wont charge to removal and refit, they'll do a changeover for the alternator so they give you a reco'd one and take yours for a reasonable price (i think cheaper than $300) or if your game enough take it off and pull it appart and check the brushes if they're worn, a brush kit with the regulator is around $80, but check the coils aswell if they're cracked etc if they area you'll need to get it fully reconditioned or changeover.

Its common for just the brushes to be worn out on alternators causing the charging system to deteriorate. Melitas is good in newport i have a friend that i went trade school with that works there, also theres one in footscray truck car marine that a reasonably priced and wont screw you around.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...