Jump to content
SAU Community

R34 Parts N Sr20de

ADDICTED2R34s
 Share

Recommended Posts

ADDICTED2R34s Rising Star

ADDICTED2R34s

Posted
Posted

i have one sr20de engine vvt out off s14 $800 has loom,airflow meter,ecu,flywheel,clutch,dumppipe has done aorund 55000kms

r34 front bar nismo has small cracks at bottem white 300 aslo have gtt wing sold!, r34gtr rear bar to suite gtt may need lil work to fit other wise goes on good is plastic bar 350 standed r34gtt nismo skirts sold!

vic melb 0408-569-537

Link to comment
https://www.sau.com.au/forums/topic/147241-r34-parts-n-sr20de/
Share on other sites
ADDICTED2R34s Rising Star

ADDICTED2R34s

Posted
  • Author
Posted

heres some pics

till i get more

post-16424-1166320605.jpg

post-16424-1166320426.jpg

3 small cracks in bottem of bar can harldy see them onely one stands out

excuse the black lines on bar was were i was going 2 cut out for cooler

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Help Understand GTT Boost Setup

      By MBS206 · Posted

      Re read everything that has been written about this in this thread.. Let us know if you're still confused.
    • joshuaho96
      Help Understand GTT Boost Setup

      By joshuaho96 · Posted

      This would be a new pump with new gears. I'm just unclear on whether it's a good idea to run more oil pump flow if you don't actually need said flow. Oil level is set a minute or so after shutting off a warm engine so wouldn't the high RPM oil level in the sump end up lower all things equal? Plan is OEM clearances, main concern in my mind is whether the OEM pump can keep up with the flow requirements of any additional oil coolers.
    • Dose Pipe Sutututu
      Help Understand GTT Boost Setup

      By Dose Pipe Sutututu · Posted

      Don't do what I did, use a 300000km old housing with billet gears. The old pump probably was clearanced with saw dust, Edward Lee's special engine treatment sauce and a good odo wind back. I had oil pressure issues, then replaces pump with new housing, new billet gears and 2x track day later binned a motor due to other oil related issues due to a previous engine builder. Long story short, buy a M2 or 3 or 4 N55/S55/S58 and enjoy life.
    • GTSBoy
      Help Understand GTT Boost Setup

      By GTSBoy · Posted

      Yeah. "New pump" does not have to mean "massive pump".
    • MBS206
      Help Understand GTT Boost Setup

      By MBS206 · Posted

      Well, can you still get an OEM pump, and by the time you're buying a Nismo/N1 etc, just buy another aftermarket pump. It's better to have the pump able to flow more if its needed, than for your pressure to drop off. At any point in time, you're replacing the oil pump in a rebuild. Aftermarket pumps are likely going to be a better economical choice, and they don't have any negatives, even if they can flow more.   Also, when you're saying "replace the pump gears" are you meaning leave a 25+ year old housing in the engine with unknown wear, and just put new gears in? As that sounds silly to me, especially if you do have that minute amount of wear, that means your new pump gears now have a little bit more clearance beside them, which means, whelp, you may not get to build a lot of oil pressure or make a lot of flow.
×
×
  • Create New...