Jump to content
SAU Community

Take Four To Work Out My Head Light Is Missing

NIZ-26T

By NIZ-26T,
in New South Wales

 Share

Recommended Posts

NIZ-26T Proficient

NIZ-26T

Posted
Posted (edited)

sunday i was pull over for loud exh pulled over by 4x4 they had me pulled over for an hour going over my car hi and lo them hi way potral came to join the fun and another all up

1 and a half hours four police men for a $77 fine and defect for air intake head light

but engineers papers do well

got off on

air filters

exhaust too loud and big

nos

too many shiny things

bov

fuel reg

braided lines

catch can

tyres too wide

big brakes not standard

harnesses

clear timing belt cover (dont see how its illeagle)

then i pulled out my paper and they had to call hiway patrol cause they didnt know shit

post-26038-1166428832.jpg

Edited by NIZ-26T
TRUBLSM Mentor

TRUBLSM

Posted
Posted

wow.. that sucks.. you should let them write all the defects and stuff and say are you done when they finish.. then show them the engineer certificate lol.. they fire up.. longest i've been pulled over for was 45 mins..

NIZ-26T Proficient

NIZ-26T

Posted
  • Author
Posted (edited)

they askeds what the switchs were in centre consol (i said for the nitrous)

they started going over the car again when hiway patrol came he said nos is ok just as long as bottle is not connected line

longest hour and a half of cop stupidity

Edited by NIZ-26T
sky017 Proficient

sky017

Posted
Posted (edited)

when i got done for speeding the other week - funny enough , i parked my car facing a wall . they didnt even check my car . and yet i have some illegal shit on the car . no engineer certificates for mods . funny the way the cops work - bastards...

Edited by sky017

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...