Jump to content
SAU Community

R32 Gtr Brake Upgrade

captain_jonno
 Share

Recommended Posts

captain_jonno Contributor

captain_jonno

Posted
Posted

Hello people.

Im picking up my 93' GTR on Friday.. I sure this has been covered before, but I just want a quick answer :laugh: I know the standard brakes are crap, but basically what is the best option as far as quality and value for money for an the upgrade & also what brake pads. Also where would I buy it from? I live in SA and car will be .. enthusiastically driven, no track work at this stage..

Cheers

Jon

Link to comment
https://www.sau.com.au/forums/topic/148050-r32-gtr-brake-upgrade/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

well the standard brakes aren't that bad for road use really. As long as the caliper is working OK (no pistons seized etc) all you really need to do is put some good fluid in and bleed it properly. If you have trouble after that maybe throw some better pads in there.

If you want to upgrade the brakes althogether you are looking at $2-6k

Roy Grand Master

Roy

Posted
Posted

Depending on how much you paid for the GTR, you may have to sell the car to pay for the brakes :)

But i would look at the rotors condition first. If they are still the std cross drilled jobbies i would replace them with new rotors, put a new seal kit through all four calipers and run good pad and fluids.

For the road they will work more then fine. If you cook your brakes on the street and you have covered the basics then you will be dead in a day or two so may as well leave some money to your family :)

Mr. Keets Grand Master

Mr. Keets

Posted
Posted

http://www.ls1.com.au/forum/showthread.php?t=62712 and slotted not drilled.

There are quite a few threads that discuss the R32 brake upgrade issue...also have alook through the old for sale threads as there is always a bit of "will it fit this" type of stuff discussed. As well as the discussion of adaptors for standard calipers top bigger disks in the suspension section

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      While it is a very nice idea to put card style AFMs into the charge pipe (post intercooler, obviously), the position of the AFM and the recirc valve relative to each other starts to become something that you really have to consider. The situation: The stock AFM is located upstream the turbo, and the recirc valve return is located between the AFM and the turbo inlet, aimed at the turbo inlet, so that it flows away from and not through the AFM. Thus, once metered air is not metered again, neither flowing forwards, or backwards, when vented out of the charge pipe. When you put the AFM between the turbo outlet and the TB, there is a volume of pressurised charge pipe upstream of the AFM and there is a volume of pressurised pipe downstream of the AFM. When the recirc valve opens and vents the charge pipe, air is going to flow from both ends of the charge pipe towards the recirc valve. If the recirc valve is in the stock location, then the section between it and the TB doesn't really matter here - you're not going to try to put the AFM in that piece of pipe. But the AFM will likely be somewhere between the intercooler and the recirc valve, So the entire charge pipe volume from that position (upstream of the AFM, back through the intercooler, to the turbo outlet) is going to flow through the AFM, get registered as combustion air, cause the ECU to fuel for it, but get dumped out of the recirc valve and you will end up with a typical BOV related rich spike. So ideally you want to put the AFM as close to the TB as possible (so, just upstream of the crossover pipe, assuming that the stock crossover is still in use, or, just before the TB if an FFP is being used) and locate the recirc valve at the turbo outlet. Recirc valve at the turbo outlet is the new normal for things like EFRs anyway. In the even of a recirc valve opening dumping all the air in the charge pipe, pretty much all of it is going to go backwards, from the TB to the recirc valve near the turbo outlet. But only a small portion of it (that between the TB and the AFM) will pass through the AFM, and it will pass through going backwards. The card style AFMs are somewhat more immune to reading flow that passes through them in reverse than older AFMs are, so you should absolutely minimise the rich pulse behaviour associated with the unavoidable outcome of having both a recirc valve and an AFM in the charge pipe.
    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Yep, in my case as soon as I started hearing weird noises I backed off the tension until it sounded normal again. Delicate balance between enough tension to avoid that cold start slip and too much damaging things.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      nvm this comment
×
×
  • Create New...