Jump to content
SAU Community

Recommended Posts

Hey guys,

Im looking at buying a car from interstate, either VIC, NSW or QLD at this stage, but I have a question some of you might be able to help me with.

If I buy a car that has interstate registration, and go to re-register it in South Australia, does it need to go through Regency, or does it just need to undergo a quick chassis/engine number check.

I have check at my local transport customer service centre, and they lady just gave me a form, told me to fill it out with the purchased vehicle's information, then take the vehicle to my local police station, where they will verify that the vin number etc is all ok and pay $44 and they will swap the rego over to SA. She said it was not a roadworthiness inspection. This would be good as the car will probably be a little bit modified and I dont want the hassle of going through Regency with my new pride and joy.

But I have also heard that EVERY single car being rego'ed in SA needs to undergo a regency inspection. I cant see how this would be the case as there must be loads of cars coming in, but if a regency inspection is required, then I'll probably can the idea of going interstate and driving it back.

If someone has been through the process and/or could shed some light on the matter, it would be greatly appreciated.

Thanks very much,

Ben

Link to comment
https://www.sau.com.au/forums/topic/148164-sa-regoing-an-interstate-regoed-car/
Share on other sites

If you get the car registered in your name in another state. you do not haver to get any checks done....as long as the car is in the name that wishes to be transfered and has current rego, you just need to go to any transport SA office. so if your worried bout mods etc that might be easier to do than changing the mods back.

I got mine from Vic..... all i had to do was go to the loacal police station get the vin and engine number checked and take the form to the rego office and there ya have it.....

This is straight from the transport sa website:

Interstate vehicle registration

You must register your vehicle in South Australia within three months if you move from another State or Territory of Australia and become a permanent resident.

Unless you hold a current interstate registration certificate in exactly the same name as the intended South Australian registration, the vehicle must undergo an identity inspection to confirm the correct identity of the vehicle. The vehicle can be inspected at the following inspection stations upon payment of the correct fee .

If you live within a 40 kilometre radius of the Adelaide GPO , the vehicle must be inspected by the:

Vehicle Identity Assessment Station and Safety Group

7 Naweena Road , Regency Park 5010

Open: 8 am – 4:30 pm, Monday to Friday (except public holidays).

No appointment is necessary.

If you live more than 40 kilometres from the Adelaide GPO , you may have the vehicle inspected at

your local police station.

Please contact the police station to arrange an appointment.

or

Vehicle Identity Assessment Station and Safety Group

7 Naweena Road

Regency Park 5010

Open: 8 am – 4:30 pm, Monday to Friday (except public holidays).

No appointment is necessary.

See vehicle inspections for more information.

Once the vehicle has been inspected, you need to present the inspection certificate or post to a Customer Service Centre along with:

your completed ‘ Application for Registration and Third Party Insurance' form

your inspection certificate

proof of identity if you have not previously been issued a licence or registered a vehicle in South Australia

the appropriate fees . Calculate applicable fees by visiting http://ecom.transport.sa.gov.au/.

The following fees may apply:

registration fee

third party insurance fee

stamp duty on insurance

stamp duty on value*

number plate fee

postage fee (if you request the number plates to be posted to you)

administration fee, level 3

Emergency Services Levy

inspection fee.

After you have registered the vehicle in South Australia , you can apply to the State where the vehicle was previously registered for a refund of registration fees.

Stamp duty*

If the vehicle was registered in your name in another State, you will need to produce the current certificate of registration from that State when you apply for registration to be exempted from paying stamp duty on the value of the vehicle.

Mr Sniper911

I purchased one of our skylines in Qld and took it to Sturt Street Police Station for the Vin check.

got mine in gold coast and went through sturt with no problems.

i recalled that the vin check station only open two days per week.

Thanks for all the replies fellas, I'm about 60kms from the Adelaide GPO so should be right to take it to the Nuri cop shop if I decide to get one. Looking at a toyota chaser for a daily driver. Hopefully it all works out...

Thanks for your help guys, much appreciated.

Ben

im doing the same procedure.its not actualy regency its another place around a few corners from there a bunch of older fellas look over it.im going to try go thru sturt to thoe ll just sey i live at victa.also will my plenum be anything to be fussed over???

487304.jpg

Just a couple of obvious things to consider.

Is the Pod secured?

What happened to the std boost controler? (hoses dont look right)

Remove the Malpassi Srising rate Reg and replace it with a std one.

Whart have you got mounted om the right hand strut tower (in front of the master brake cylinder)? Alarm?

Where/what has happened to the BOV, is it still a return system?

These are just some of the things I can see (a larger pic would help) that might be of interest to the MVI unit.

Im not trying to give you a hard time, just point out the things that caught my eye (and I assume they see a lot of skylines)

Edited by 4door_Sleeper

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
    • Every one has seemed to of have missed . . . . . . . The Mazda Cosmo . . . . . . what a MACHINE ! !
×
×
  • Create New...