Jump to content
SAU Community

Recommended Posts

Hey guys,

Im looking at buying a car from interstate, either VIC, NSW or QLD at this stage, but I have a question some of you might be able to help me with.

If I buy a car that has interstate registration, and go to re-register it in South Australia, does it need to go through Regency, or does it just need to undergo a quick chassis/engine number check.

I have check at my local transport customer service centre, and they lady just gave me a form, told me to fill it out with the purchased vehicle's information, then take the vehicle to my local police station, where they will verify that the vin number etc is all ok and pay $44 and they will swap the rego over to SA. She said it was not a roadworthiness inspection. This would be good as the car will probably be a little bit modified and I dont want the hassle of going through Regency with my new pride and joy.

But I have also heard that EVERY single car being rego'ed in SA needs to undergo a regency inspection. I cant see how this would be the case as there must be loads of cars coming in, but if a regency inspection is required, then I'll probably can the idea of going interstate and driving it back.

If someone has been through the process and/or could shed some light on the matter, it would be greatly appreciated.

Thanks very much,

Ben

Link to comment
https://www.sau.com.au/forums/topic/148164-sa-regoing-an-interstate-regoed-car/
Share on other sites

If you get the car registered in your name in another state. you do not haver to get any checks done....as long as the car is in the name that wishes to be transfered and has current rego, you just need to go to any transport SA office. so if your worried bout mods etc that might be easier to do than changing the mods back.

I got mine from Vic..... all i had to do was go to the loacal police station get the vin and engine number checked and take the form to the rego office and there ya have it.....

This is straight from the transport sa website:

Interstate vehicle registration

You must register your vehicle in South Australia within three months if you move from another State or Territory of Australia and become a permanent resident.

Unless you hold a current interstate registration certificate in exactly the same name as the intended South Australian registration, the vehicle must undergo an identity inspection to confirm the correct identity of the vehicle. The vehicle can be inspected at the following inspection stations upon payment of the correct fee .

If you live within a 40 kilometre radius of the Adelaide GPO , the vehicle must be inspected by the:

Vehicle Identity Assessment Station and Safety Group

7 Naweena Road , Regency Park 5010

Open: 8 am – 4:30 pm, Monday to Friday (except public holidays).

No appointment is necessary.

If you live more than 40 kilometres from the Adelaide GPO , you may have the vehicle inspected at

your local police station.

Please contact the police station to arrange an appointment.

or

Vehicle Identity Assessment Station and Safety Group

7 Naweena Road

Regency Park 5010

Open: 8 am – 4:30 pm, Monday to Friday (except public holidays).

No appointment is necessary.

See vehicle inspections for more information.

Once the vehicle has been inspected, you need to present the inspection certificate or post to a Customer Service Centre along with:

your completed ‘ Application for Registration and Third Party Insurance' form

your inspection certificate

proof of identity if you have not previously been issued a licence or registered a vehicle in South Australia

the appropriate fees . Calculate applicable fees by visiting http://ecom.transport.sa.gov.au/.

The following fees may apply:

registration fee

third party insurance fee

stamp duty on insurance

stamp duty on value*

number plate fee

postage fee (if you request the number plates to be posted to you)

administration fee, level 3

Emergency Services Levy

inspection fee.

After you have registered the vehicle in South Australia , you can apply to the State where the vehicle was previously registered for a refund of registration fees.

Stamp duty*

If the vehicle was registered in your name in another State, you will need to produce the current certificate of registration from that State when you apply for registration to be exempted from paying stamp duty on the value of the vehicle.

Mr Sniper911

I purchased one of our skylines in Qld and took it to Sturt Street Police Station for the Vin check.

got mine in gold coast and went through sturt with no problems.

i recalled that the vin check station only open two days per week.

Thanks for all the replies fellas, I'm about 60kms from the Adelaide GPO so should be right to take it to the Nuri cop shop if I decide to get one. Looking at a toyota chaser for a daily driver. Hopefully it all works out...

Thanks for your help guys, much appreciated.

Ben

im doing the same procedure.its not actualy regency its another place around a few corners from there a bunch of older fellas look over it.im going to try go thru sturt to thoe ll just sey i live at victa.also will my plenum be anything to be fussed over???

487304.jpg

Just a couple of obvious things to consider.

Is the Pod secured?

What happened to the std boost controler? (hoses dont look right)

Remove the Malpassi Srising rate Reg and replace it with a std one.

Whart have you got mounted om the right hand strut tower (in front of the master brake cylinder)? Alarm?

Where/what has happened to the BOV, is it still a return system?

These are just some of the things I can see (a larger pic would help) that might be of interest to the MVI unit.

Im not trying to give you a hard time, just point out the things that caught my eye (and I assume they see a lot of skylines)

Edited by 4door_Sleeper

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • had 4 weeks off over xmas and well did some stuff to the shed and BRZ, well short of is I don't work full time in supercars anymore as of yesterday.........
    • Did you get any down time over Christmas, or have you had any since to play with this? Or have you given up and are trying to get yourself a second hand V8SC instead?
    • A random thought I had just before I hit "Submit on this post". If brake fluid, in a container in my garage that has never been opened goes bad after 18 months, why can I leave it in my car for 24 months in an "unsealed container"... Secondly, some other digging, and brake fluid manufacturers seem to be saying 5 year shelf life... Me thinks there line on 18 months for an unsealed bottle is pretty much horse shit marketing spin. Kind of like how if you drive a car and don't run a turbo timer your turbo and motor will die horribly...   Where I started on this though... Someone (me) started down a bit of a rabbit hole, I don't quite have the proper equipment to do Equilibrium Reflux boiling per the proper test standards. I did a little digging on YouTube, and this was the first video I found on someone attempting to "just boil it". This video isn't overly scientific, as we don't have a known reference for his test either. Inaccuracy in his equipment could have him reaching the 460 to 470f boiling point range in reality. In the video, using a laser temp gun, he claims his Dot3 that's been open in his florida garage for over a year gets to about 420 to 430 fahrenheit (215 to 221c) Doing some googling, I located an MSDS for that specific oil, and from new, it claims a dry boiling point of 460 to 470f. Unfortunately they don't list a wet boiling point for us to see how far it degraded toward its "wet" point. While watching it I was thinking "I wonder what the flash point is..." turns out its only 480f for that specific brake fluid....   As for testing the oil's resistance, I might not be able to accurately do that unfortunately. Resistance level will be quite a LOT higher than my system can read I suspect based on some research. However, I might be able to do it by measuring the current when I apply a specific voltage. I won't have an actual water % value, but I'll have some values I can compare between the multitude of fluids. I'll run some vague calculations later and see if I should be able to read any reliable amount of current. These calcs will be based on some values I've found for other oils, and see how close I'll need my terminals together. From memory I can get down to 1pA accuracy on the DMM. I don't think my IOT Power Tester has any better resolution.    
    • No, with a twin plate clutch flywheels and clutch pressure plate/friction disks go together. Only clutch where that isn't the case is the Uniclutch but they currently don't make a pull version for the Getrag R34, just some other cars. Personally the flywheel is as light as I'd want it to be. It already drops revs faster than I want to shift normally and I blip the throttle again to rev match on upshifts.
    • Are there any other lighter flywheels that can be used with nismo coppermix twinplate system? Id like to gave the revs pick up faster than oem
×
×
  • Create New...