Jump to content
SAU Community

What Is The Legal Db Limit For Exhaust In Nsw?

Munkyb0y

By Munkyb0y,
in New South Wales

 Share

Recommended Posts

GreddyGo Rising Star

GreddyGo

Posted
Posted

I don't think it's as easy as holding it a 4800, they measure when you back off from that so incase it backfires and getting to that RPM, I have done ir before at work for a blue slip and tafe.

They also test starting your car

Cheers

Josh

Munkyb0y Grand Master

Munkyb0y

Posted
  • Author
Posted (edited)

faaaarken hell. my exhaust is 102dB WTF???

i held 3500, then held 4800, then back down. the highest reading was 102db.

and to make things worse, we couldnt fit the oval resonator on, coz there's not enough room under there.

that would have only brought it down maybe 3dB anyway. but the only option is to put a hotdog resonator which will only reduce it by maybe 1 or 2 dB.

dangnamit :laugh:

the way he measured it was 45degrees left of the tailpipe, about 1metre away. is it possible he was too close? i might go somewhere else and get a reading.

edit:

before my highflow cat, the exhaust didnt seem this loud. i assume the cat has increased flow dramatically, causing increased volume.

i didnt expect it. is this pretty normal of a highflow cat? it's only an xforce 3 inch cat (replaced a standard compliance cat).

Edited by Munkyb0y
Zane Enthusiast

Zane

Posted
Posted

I had my exhaust tested a few years back and I'm sure things haven't changed much.

The process back then was:

Place the microphone at 45deg and 0.5m from the end of tailpipe.

Increase revs gradually to 75% of max hp of engine (this turned out to be 4200rpm for a skyline (any model skyline??) as indicated in the EPA manual, I didn't argue for a more accurate figure because more revs = more noise). Increase in revs has to be gradual so the reading does not spike, otherwise they have to start again. Same goes for backing off. They are not measuring dB under acceleration, they are measuring a simulated drive by situation at constant engine revs.

This process was repeated exactly when I fixed the exhaust and was retested.

I'm running a 3" front pipe off the standard dump, 3" high flow CAT, into 3" pipe with a hotdog inline with a small box resonator, and a 6" barrell muffler with a 4" tip. Tested at 89dB.

Without the box resonator I was tested (and fined) at 92dB. A hotdog will only knock off 1-2 dB. NSW EPA regulation is a maximum reading of 90dB.

Z.

Munkyb0y Grand Master

Munkyb0y

Posted
  • Author
Posted
I had my exhaust tested a few years back and I'm sure things haven't changed much.

The process back then was:

Place the microphone at 45deg and 0.5m from the end of tailpipe.

Increase revs gradually to 75% of max hp of engine (this turned out to be 4200rpm for a skyline (any model skyline??) as indicated in the EPA manual, I didn't argue for a more accurate figure because more revs = more noise). Increase in revs has to be gradual so the reading does not spike, otherwise they have to start again. Same goes for backing off. They are not measuring dB under acceleration, they are measuring a simulated drive by situation at constant engine revs.

This process was repeated exactly when I fixed the exhaust and was retested.

I'm running a 3" front pipe off the standard dump, 3" high flow CAT, into 3" pipe with a hotdog inline with a small box resonator, and a 6" barrell muffler with a 4" tip. Tested at 89dB.

Without the box resonator I was tested (and fined) at 92dB. A hotdog will only knock off 1-2 dB. NSW EPA regulation is a maximum reading of 90dB.

Z.

i'm running the exact same setup as you, minus the box resonator and hotdog. where the hell did u get the box to fit? if i put it on, it would be hanging way too low, or touching the tailshaft. mine is all mandrel bend, so it kinda takes up alot of room with no harsh bends.

i reckon maybe this guy got the reading wrong, coz the revs didnt increase gradually, i remember punching it a little between 3500 and 4800, coz i was using my left foot, and was only half in the car :laugh:

although it would still be over legal limit, i have no doubt.

Zane Enthusiast

Zane

Posted
Posted

The hotdog and the box resonator only have about 3 inches of pipe between them and they fit between the CAT and the bend before the diff. The box is about 25cm x 20cm so is pretty small. All my pipes are mandrell bent and I had it made to sit as close to the body as possible so I have max ground clearance.

If your over 100dB you may need to look at a bigger rear muffler as well.

RellikZephyr Proficient

RellikZephyr

Posted
Posted

The Ruling is...

Passenger Vehicles Made:

Before March 1985 96 dB

After March 1985 90 dB

R33 GTST

Engine Test Speed 4800 Rpm

Microphone placement

45 Degrees angle +/- 10 degrees

same hieght as exhaust tip +/- 25mm

distance from outlet 525mm +/- 25mm

This info taken straight from EPA and Testing Procedure Manuals

can post em up if you want...

Cheers

RellikZephyr

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Possible swap on R34 RB20DE NEO?

      By GTSBoy · Posted

      If the RB29 box in the car is a push clutch, then yes, you will need to deal with the pull clutch on the turbo box. You either buy a pull clutch and don't use the old one, or you do the things needed to convert the turbo box's clutch arrangement over to push. Which is a bit of a f**karound. "Making" a custom tailshaft is the easy part. But you will need to source the front clip yoke - the bit that goes into the output of the gearbox. These are not as easy to find. They are out there, but they don't grow on trees the way that they used to.
    • GTSBoy
      Turn signal wiring question

      By GTSBoy · Posted

      Indicator bulbs are way too bright to use as a "corner marker" (we call them parking lights too). Sure. Go ahead and do it. But realise that you wil need to come up with all your own wiring to do it, as no-one will have a standard howto worked out for Skylines. It's just a matter of abandoning everything that Nissan have done and starting from scratch. You'd probably be better off retrofitting tailght/brakelight globe bases into the front indicator housings and using the taillight circuit for your corner marker and the brake light as the indicator. You'd need to work out how to kill the marker circuit while the indicator is flashing, otherwise it won't flash on-off, just bright-less bright.
    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
×
×
  • Create New...