Jump to content
SAU Community

Recommended Posts

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Cheers huddy.

Its for a small person. Like Huddy. WInk Wink Nudge Nudge, ayyyyyy huddy. Feel like a new comfy seat.

Tony,

Its a small seat. As in very squishy. no offence at all but i met u out at Mallala when you were talking to Mark & Julie. You might be to tall and have broader shoulders, so it might be to small for you.

Pics below.

02-02-07_0849.jpg

02-02-07_0850.jpg

Cars at Doyles now.

Front end is getting fixed.

Top rad support and right skirt/ battery tray is all fixed and primed or what ever they are doing.

Painting bonnet white instead of black again. Maybe a good maybe a shit thing. Oh well.

I also have my original engine at home. SO parts are going like hotcakes. Ovver me $$$ for parts. No offer refused as i want the block gone asap.

Lub you ryan

Head/ turbo/ injectors and exhaust manifold sold. Pending payment.

But nothing is for certain yet.

$600 and u can have the lot huddy.

I really dont know what its worth and what bearing/s have gone?

I really want to find out though.

But oh well. Car should be coming back today. Hopefully.

YAYAYAYAYAYA

  • 2 weeks later...

Ignition problem sucks. 18 coil packs and finidng out which ones work and dont is even worse.

Yeh Jetpower or whatever they are called for testing every single coil pack for me.

I have to have atleast 6 that work fine I hope.

Edited by R32_4door_drifting

I have found the rims/ coilovers and a front mount kit now.

SO RYAN. DOnt sell those rims that were on the black R33. the ones u have for $2000. and those buddy clubs. I will put a deposit down for them if u want.

Car will be half decent soon.

Love you all and goodnight

Edited by R32_4door_drifting

Enki Gspec, 18" x 9" + 10", 114.3mm PCD, 5 Stud.

Nissan Skyline R32 Buddy Club coilovers

And a Greedy Frount Mount Kit for $600 from a sponsor.

Dammit.

Now someone give me some f#$king good coil packs as mine are all roasted and need some new ones I think. Havent heard back from the tester place so not expecting good news.

Edited by R32_4door_drifting

Its not necessarily the coil packs, I got spitfires and still get a miss at 5500, I think its just running ridiculously rich (below 10:1) and causing it. With the splitfires its not as bad and doesn't happen as often however.

nice one Brenton

good work on keeping your car better the devil you know I say plus you gotta mod it a bit more before we can do a straight swap

lol

im assuming by modding it a bit more you want him to put a 25 in it for you?

ahh ryan i remember the day you were "25's are shit... 20's rock"

*slaps you*

20's for the win!

maybe check fuel pump/fuel filter/fuel reg also brenton?

did you use the injectors off of your old engine? if not maybe try swapping those over!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...