Jump to content
SAU Community

Recommended Posts

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Now someone give me some f#$king good coil packs as mine are all roasted and need some new ones I think. Havent heard back from the tester place so not expecting good news.

Rip them out and shove silicon all around them... Worked on mine. :spank:

  • 2 months later...

What size rims can u fit on the rear?

I recently had a set of 18 x 9's on the rear and they hung out slightly, the front 18 x 8's they sat just right, I tried them on the rear and they too sat perfect.

So 8" wide rim +35 tends to fit just nice. :)

lol looks nice, I have the same prob with my new rims, they stick out too much :teehee:

They fit perfectly.

The tyre wall is flush with my gaurds. On the rear anyway.

The rims are 18 x 9 +10 both front and rear.

I will need to get camber arms asap for the front.

Thanks SHowza.

Lol i was the freak at AIR yesterday waiting for huddy's tyres to be fitted yelling abuse at ya. HAHAHAHAH

Yeah but the rim itself looks to be sticking out.

Yes that is correct.

I am under the impression that if the tread is under the gaurd its A OK!

So yeh the rim sticks out of the gaurd but the treadis still under the gaurd.

I dont care it looks fat.

  • 5 months later...

Yeh I havent replied in this for a while.

But the broom broom has changed alot since i last posted.

04-09-07_1213.jpg

04-09-07_1218.jpg

P9300031.jpg

P9300043.jpg

SAUSunday12.jpg

Entry.jpg

It also now has a roof spolier on the rear window and will be getting a supermade boot spoiler on it soon aswell.

YAY.

Brenton

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...