Jump to content
SAU Community

Sold

kjb_r33

By kjb_r33,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

kjb_r33 Experienced

kjb_r33

Posted
Posted (edited)

Have owned car for 4 years.

Completely stock with the exception of a rb20 wastegate actuator.

Few marks in the interior and could use a paint job, but other than that its a great reliable car.

Within the last 2 years its had a new water pump and timing belt fitted.

Only reason im selling this is because i also have a r32 and a 300zx, its just not getting driven enough and its a shame to see it sitting there.

The following pics are a few years old now, will get some current ones tomorrow. Same car, just has a bit of paint fade and stone chips at the front.

post-536-1166825010.jpg

post-536-1166825026.jpg

post-536-1166825043.jpg

Looking for 6500. So low mainly due to the fact that it does need a paint job.

EDIT: Forgot to add, its got 140,000 k's on it

Edited by kjb_r33
Link to comment
https://www.sau.com.au/forums/topic/148451-sold/
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
  • 1 month later...
  • 1 month later...
  • 4 weeks later...
  • 2 weeks later...
  • 2 weeks later...
webber Proficient

webber

Posted
Posted

Sold to me,

Thanks Ken,

Going in for a minor Straight and Paint this week, i will send you photo's when it is done.

Drove it home well over 700KM's did not miss a single beat

P.S. the other item is in a post pack waiting for the post office to open tuesday.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/148451-sold/#findComment-3170986
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
×
×
  • Create New...