Jump to content
SAU Community

R32 Bits For Sale

6pistons
 Share

Recommended Posts

6pistons Enthusiast

6pistons

Posted
Posted (edited)

Hey fellow Skyliners...

Got some R32 bits for sale:

1. 2xCastor Rods with Whiteline bushes- $90

2. Arm Pad Rest - $20

3. Power Windows Controller - $40

4. Stock Steering Wheel horn(Skyline Badge) - $10

5. R32 Steering Wheel(mint condition) - $100 (Sold)

6. Speedo Surround - $40 (Sold)

7. Skyline Car Mats (Full Set) - $80 (Sold)

8. Calsonic Intercooler, 63x29x6cm (couple of dints) - $75 (Sold)

9. HKS Super Dragger Exhaust (A little dinted)- $75 (Sold)

10. Centre Console Panel $30 (Sold)

11. Left Head Light - $50 (Sold)

12. R32 Air Filter Box - $50 (Sold)

13. Front Whiteline Anti-Roll Bar(Almost brand new) - $110 (Sold)

14. Rear Whiteline Anti-Roll Bar(Almost brand new) - $110 (Sold)

15. Speedometer (129000km) - $40 (Sold)

16. Autometer Boost Gauge (small) - $50 (Sold)

17. Ashtray - $10 (Sold)

18. Koni Dampers and King Springs (Stiff-Almost brand new)- (Sold)

19. A/C Front Panel - $10 (Sold)

Reasonable offers would not be refused.

PM me for details. Located in Central Coast. Call me at 04 22 77 1359.

post-10984-1167052720.jpg

Edited by 6pistons
Link to comment
https://www.sau.com.au/forums/topic/148697-r32-bits-for-sale/
Share on other sites
6pistons Enthusiast

6pistons

Posted
  • Author
Posted

NismoR31Jet - I have to check the sizes for you. Will get back to you ASAP.

DFAULT - You got PM.

Sarumatix - Sorry, steering wheel is considered sold to someone else for the time being...

Cheers.

What size is the intercooler core? What size are the pipes on the end tanks?

What size is the pipe into the muffler?

6pistons Enthusiast

6pistons

Posted
  • Author
Posted (edited)

Hi ToF,

I am pretty sure the mounts are still good. I have put up the pics for your review.

And no, I don't have the right side.

Cheers.

Got a pic of the left headlight? Are the mounts on them still good?

You wouldn't have the right one by any chance would you?

Edited by 6pistons
6pistons Enthusiast

6pistons

Posted
  • Author
Posted (edited)

NismoR31Jet - The size of the core is updated as above. Pipes on the end tanks are 8cm in diameter.

Diameter of the pipe into the muffler for the Super Dragger Exhaust is 8.5cm. It has a flange for bolting onto.

Rekin - sorry no vents.

What size is the intercooler core? What size are the pipes on the end tanks?

What size is the pipe into the muffler?

Edited by 6pistons
6pistons Enthusiast

6pistons

Posted
  • Author
Posted

The given dimensions are just the rectangular "core" itself...

The whole intercooler is definitely longer, length wise, together with the end pipes and its connection. Is this the dimension you are looking for?

Let me know... I am here to help to the best of my ability. :yes:

Cheers.

The pic of that cooler and the dimensions you give dont seem to match :S

Just that im interested

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...