Jump to content
SAU Community

Recommended Posts

Hi,

I've just purhcased the following parts

Power FC

R34 N1 turbos

trust dumps and front pipe

catco cat

i've got a stardard R32 at the moment.

what kind of power can i expect from this setup (safely)

Also, will the stardard clutch hold? should i wait for it to start sliping then get a new jim berry one?

Link to comment
https://www.sau.com.au/forums/topic/148911-gtr-setup-advise/
Share on other sites

Car should be great as long as you have a healthy engine.

You should probably upgrade the fuel pump and injectors just so it can all be done in one tune.

I just have power fc, 550cc injectors, front pipe back exhaust and run 1 bar boost = 225awkw and 253 rwkw.

Car should be great as long as you have a healthy engine.

You should probably upgrade the fuel pump and injectors just so it can all be done in one tune.

I just have power fc, 550cc injectors, front pipe back exhaust and run 1 bar boost = 225awkw and 253 rwkw.

Injectors should be fine. I'm not chasing anymore power.

change the rod bolts on your engine, they are the weak point in the bottom end, put in the injectors, and the pump as stated above, your car is old and will suffor easily from fuel starvation due to the old pump.

change the rod bolts on your engine, they are the weak point in the bottom end, put in the injectors, and the pump as stated above, your car is old and will suffor easily from fuel starvation due to the old pump.

that's pretty random, suggesting changing something in the bottom end for someone who's only doing bolt ons. I think if he was going to do that there's a load of other things he should do while he's down there.

But randomness aside you should definitely run a new fuel pump and consider having your injectors professionally cleaned and flow tested or just drop some sard or nismo injectors in.

Standard clutch will already be shagged if it's not a new one. Probably best to budget for that straight up.

Just change the rod bolts? wtf is all i have to say to that.

Its totally uselsss unless your doing a bottom end rebuild. Why do something that requires motor out/apart just to change a few bolts?

2+2=15 on that one.

Anyhow, firstly you need a full exhaust to go with the front pipe etc.

You didnt list it, so ill assume you dont have it.

You'll need a clutch also.

Injectors will limit the power you will make with the R34N1s as they will make more power than the stockers can handle, but if you keep power to 270-300rwkw then you will be fine.

You'll also need a fuel pump

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Shove more foam in it as a minimum if you possibly can. Or steel wool (not the stuff with soap on it!) Baffles / getting the oil out of the air is huge, and should be done at both the cam cover, and the catch can.   I'm about to do a power steering reservoir, and even that needs some thought to make sure air is separated from the oil, to stop evil Cavitation. I'll probably look at doing my own catchcan later on too.
    • I was once told, who it was I'm to old to remember, that the length of the OEM wheels brace supplied with a vehicle is designed long enough for a average person to apply enough torque to do up, and undo the wheel nuts to the specified torque  What a average person is is anyone's guess though, i.e. average fat bastard, average knuckle head, average perfect sized human......like me Unless of course, a tyre shop has ugga dugga'd them up to "torque to yeild/strip" specs, used cross threading as natures lock tight, or a big breaker bar was used to tighten them up to get some nice stretch in the poor old wheel studs Me, I torque wheel nuts to 1 elbow joint click, lower torque settings are based of wrist clicks, higher torque settings are based of shoulder clunks, or total dislocation for anything that requires all of the torques 
    • I think the catch can design is pretty flawed. Evident in the fact that the V2 one moved to a larger top mounted filter which alone would have helped with overflow and reduce restrictions compared with the side filter. I also imagine there was a major improvement to the baffling design. It is worth mentioning that this catch can with the RB20 was never as much of an issue and the high kms RB25 is likely a part of the problem. I have gotten quotes for both a new "Vibrant Gen 3" catch can and to modify this existing ones but that may have to wait until after the track day. I hope the sump/head breathers/drains and cam splash plates will be enough
    • Yep, both. The ratio is 1.8 instead of OEM being 1.7. The rocker bodies are modified with a larger bolt hole and re-threaded with 10mm holes instead of the 8mm YT has stock. Finding out they don't actually fit the stock castings cause a lot of un-impressment by the person in the USA who tapped the new holes for the 'upgraded' YT product. He was very unhappy with them given their previous design did not require 'clearancing'
    • That too, but I think this is why she's put the work into the cam cover baffles. I mean, a catch can should only need to be a catch can, not an oil air separator also. Not to say that putting the effort into having it do a better job of oil-air sep is a waste of time, but doing the sep earlier is always going to make life better. And that should happen now anyway.
×
×
  • Create New...