Jump to content
SAU Community

New Dash Console - Pics

sky017

By sky017,
in Exterior & Interior Styling

 Share

Recommended Posts

TramanBaba Community Regular

TramanBaba

Posted
Posted
hey guys im a brand new skyline owner.

was lookin through this thread, some awesome results here and seeing as how my interior is a bit rough i just have to do this too.

ive got a bit of a noob question though... how do i remove the dash panels? i dont wanna break anything so i thought i'd ask first.

I'm thinking a dark silver might go well with a black skyline. What do you think?

thanks!

There are posts in teh DIY section... Anyways you need to pull the panels out, disconnect the main housing panel, i.e. various plugs that you just be able to clip out and that's about it really. For the driver's arm control removie the plug in the cup, unscrew it and pull it out carefully. If you need pics I could email them you. Good luck. To the thread starter.. once again this really is a fantastic thread. For the cost you get soo much more value and satisfaction. Cheers.

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Rudager Enthusiast

Rudager

Posted
Posted (edited)

Had a go today, completly botched it, musn't have shaken the primer enough and was spitting everywhere, didn't use a high enough sandpaper so got fairly noticeable scratches everywhere.

So gunna goto supercheap tomorrow (hope they're open) get some 100,200,400,600 and 2000 grit sandpaper, another can of primer and the silver paint i picked out. Sand off all the old paint then work it up from 100 to 2000 grit to get a nice smooth surface, 2-3 coats of primer 2-3 coats of Mercury Silver or whatever it was and 2-3 coats of clear coating.

Will let you guys know how it turns out :sick:

EDIT: Just a quick question, how is everyone supporting the parts while they paint them, i've just had them lying on the ground, just so hard to get a nice even coating though, was going to hang it from the clothsline but it's right under a tree and didn't want shit falling off it

Edited by Rudager
TramanBaba Community Regular

TramanBaba

Posted
Posted
Had a go today, completly botched it, musn't have shaken the primer enough and was spitting everywhere, didn't use a high enough sandpaper so got fairly noticeable scratches everywhere.

So gunna goto supercheap tomorrow (hope they're open) get some 100,200,400,600 and 2000 grit sandpaper, another can of primer and the silver paint i picked out. Sand off all the old paint then work it up from 100 to 2000 grit to get a nice smooth surface, 2-3 coats of primer 2-3 coats of Mercury Silver or whatever it was and 2-3 coats of clear coating.

Will let you guys know how it turns out :sick:

EDIT: Just a quick question, how is everyone supporting the parts while they paint them, i've just had them lying on the ground, just so hard to get a nice even coating though, was going to hang it from the clothsline but it's right under a tree and didn't want shit falling off it

yea i did mine last week and had them lyin on teh garage floor. Turned out fine. Make sure you spray one section at a time. Don attempt to spray a whole piece in one go with the finger on the nozzle. results don turn out good that way. Anyways supercheap will be open tomo ( i enquired, need to get a jack off them :D). good luck with your rejob.

ak_stylez Community Regular

ak_stylez

Posted
Posted (edited)
There are posts in teh DIY section... Anyways you need to pull the panels out, disconnect the main housing panel, i.e. various plugs that you just be able to clip out and that's about it really. For the driver's arm control removie the plug in the cup, unscrew it and pull it out carefully. If you need pics I could email them you. Good luck. To the thread starter.. once again this really is a fantastic thread. For the cost you get soo much more value and satisfaction. Cheers.

hey I'm having trouble with this part here:

http://members.iinet.com.au/~ahmedk/07-04-07_1412.jpg

how can i disconnect the switch and light so that the panel can come out? also same problem with the antenna switch on the other side of the steering wheel.

on a side note, how many of you had missing screws behind the ashtray etc? :D

thanks!

Edited by ak_stylez
Rudager Enthusiast

Rudager

Posted
Posted
hey I'm having trouble with this part here:

http://members.iinet.com.au/~ahmedk/07-04-07_1412.jpg

how can i disconnect the switch and light so that the panel can come out? also same problem with the antenna switch on the other side of the steering wheel.

on a side note, how many of you had missing screws behind the ashtray etc? :thumbsup:

thanks!

The mirror switch i got a flathead screwdriver and lever'd it out from the front, just be careful not to put too much pressure on the dash plactic's.

TramanBaba Community Regular

TramanBaba

Posted
Posted
hey I'm having trouble with this part here:

http://members.iinet.com.au/~ahmedk/07-04-07_1412.jpg

how can i disconnect the switch and light so that the panel can come out? also same problem with the antenna switch on the other side of the steering wheel.

on a side note, how many of you had missing screws behind the ashtray etc? :thumbsup:

thanks!

yup just lever it out with a flathead screw driver. It shouldnt take too much effort to get it out. Then disconnecthe plug for the mirror controllers. Am sure you'll have something similar for the alarm LED as well. And I dont know about others, but i have my ashtray screws intact :)

Basti Grand Master

Basti

Posted
Posted

no need for a flathead. just reach behind and squeeze the clips on the back together. should make it pop out. no worries bout scratches that way. its how i did it from memory. if you want confirmation im gonna be pulling my dash out on either monday or tues. can tell u for sure then.

with the light, if it isnt obviously slotted in then just cut the wire behind it. no harm to ur alarm and easily reconnected later

  • 8 months later...
XRAIDER Enthusiast

XRAIDER

Posted
Posted

I finaly got around to doing mine, didn't use a clear coat and it shouldn't scratch. Went a bit further and painted the cluster surround and the climate control panel.

I want to paint the passenger air vent and all passenger window switches one day to finish it off, but this will do for now. :)

Before and after pics

post-33491-1197100976_thumb.jpg

post-33491-1197101034_thumb.jpg

post-33491-1197101115_thumb.jpg

post-33491-1197101177_thumb.jpg

P.S The Taco is stuffed i tried to fix it it worked for a day then stopped again doh!

XRAIDER Enthusiast

XRAIDER

Posted
Posted
XRAIDER i like that job man. any reason y u didnt go the clear on top? oh and you forgot the ashtray

Hey thanks buddy, I didn't want a clear coat mainly because of the sun reflection, and I ran out of paint just as I finished off the climate control panel, I'll do it when I do the passenger door switches and the passenger vent.

Cheers :D

  • 1 month later...
Endorean Proficient

Endorean

Posted
Posted

Just a quick one, I've read through the post and have not found the answer.

How are you taking the rubber coating off the dash parts before painting. I want to try the Model paint method that was mentioned previously in the thread.

Cheers.

Basti Grand Master

Basti

Posted
Posted

i used sandpaper. bad idea this. lots of work and i had a lot of scratches left to fix afterwards. try either metho or turps. one or the other causes the rubber to deform, making it easy to remove. i found this out rite at the end.

  • 2 months later...
uneek Enthusiast

uneek

Posted
Posted

Well I've done my dash and other surrounds. Wont be doing it again in a hurry, but I did scratch it putting it back in...so maybe next Easter. Looks like I've gone a step further and done the door handles and side pockets of the door as well as the vents. I'd also like to do the demister vents, but have really had enough of this entire process!

I rubbed most of the rubber off by hand. Metho works and so does Acetone, but you still need to give it some elbow grease. Few coats of primer, few coats of paint and quite a few coats of acrylic top coat clear.

Main dash

post-47247-1206168499_thumb.jpg

Driver door

post-47247-1206168525_thumb.jpg

Passenger door

post-47247-1206168542_thumb.jpg

Fairly impressed with the result.

  • 7 months later...
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Hypergear Turbochargers and High flow Services Development thread

      By Watermouse · Posted

      Ahh ok, thanks again for your valued insight Tao
    • MBS206
      R32 GTS (RB20DE) clogged cat

      By MBS206 · Posted

      The hot exhaust light will come on not from just the cat being blocked, but it's just a temp sensor, and it's designed to warn you to not do things like park in long grass.   If you've been pushing the motor a bit, it can cause the light to come on.   Second if the cat is rattling, I'd suspect it's not blocked, but instead falling apart inside.   The easiest "fix" until you can get a cat put back in, is to unbolt your one, bash the rest of the insides out, and then bolt it back in.   For a daily driver/street car, I am in agreeance of put a cat in the car. If it were race car I wouldn't care if it were removed.
    • Sean'O
      3D printing fun

      By Sean'O · Posted

      No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Duncan
      3D printing fun

      By Duncan · Posted

      Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
    • Duncan
      R32 GTS (RB20DE) clogged cat

      By Duncan · Posted

      I'm not sure what sort of shops are nearby, but I'd expect any reasonable exhaust shop could put a cat in it that will not restrict the power that engine makes. Otherwise, if you want to remove it, short lengths that replace the cat are readily available online, search for "de-cat pipes" or "test pipes"  
×
×
  • Create New...