Jump to content
SAU Community

Recommended Posts

HI all,

I'm looking at the seat covers (full package) being offered in http://www.skylinesaustralia.com/forums/in...howtopic=140189

but I don't have the time or patience to install them myself. Are there any recomendations for someone to do it who won't wreck the car?

As a side note any colour combinations you would recomend for a silver GTR (red/black too striking and plain black looks a bit average)

Well top cat have fitted two of these leatherette covers and won't touch them again. Too much trouble installing them. Tried to get me to purchase a $3300 leather set....let me think...no.

Does anyone have these covers and are willing to show them. GTR in particular but just seeing the general quality on any car would be good.

Dark gray/blue seems to be a likely option.

And I'll vouch for Anthony's experience here;if you've seen his car,you'll know what I'm referring too-gorgeous job,mate!

I've used Capital Transport Upholstery(Phil) in Hume for various jobs over the years;price was slightly higher than some quoted,and the workshop isn't flash,but the jobs were always top notch. Could be worth a look,JB.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...