Jump to content
SAU Community

Recommended Posts

Hey guys, i have been having an intermittent problem with my r33 gtst for a few weeks now. when driving along, it just stops firing on all cylinders and dies, but picks up again before it stalls. i have just replaced the coils and plugs, so i think it may be the crank sensor. has anyone ever experienced a similar problem before?? its really bugging me and any insight as to what may be wrong would be greatly appreciated :laugh:

Thanks, Bill

Link to comment
https://www.sau.com.au/forums/topic/150184-electrical-problems/
Share on other sites

I too am having the same problem. My car is an R33 S2 GTST Automatic. It has been stalling while idling at the lights and in some cases takes a while to start after stalling. I have also noticed revs dropping significantly while driving and the accellerator feeling sticky when this happens. Stalled as i was taking off from the lights last night.

Car has been with the mechanics twice who have still not figured out the problem. First time in, they changed the oxy sensor which made no difference at all, 2nd time in they found a fault with the wiring harness for the air flow meter and fixed. Car ran beautifully after this for 3 to 4 hours before stalling again in idle and then 30 mins later, stalling on take off from the lights as mentioned.

My mate was with me and thinks but is not sure that it could be the crank angle sensor and from reading topic "Sticky: Missfire Boost.." it seems other people have had this problem and was solved by changing the crank angle sensor.

My advice, if it's only just started to happen, get it looked at quickly because it gets worse quick.

I too am having the same problem. My car is an R33 S2 GTST Automatic. It has been stalling while idling at the lights and in some cases takes a while to start after stalling. I have also noticed revs dropping significantly while driving and the accellerator feeling sticky when this happens. Stalled as i was taking off from the lights last night.

Car has been with the mechanics twice who have still not figured out the problem. First time in, they changed the oxy sensor which made no difference at all, 2nd time in they found a fault with the wiring harness for the air flow meter and fixed. Car ran beautifully after this for 3 to 4 hours before stalling again in idle and then 30 mins later, stalling on take off from the lights as mentioned.

My mate was with me and thinks but is not sure that it could be the crank angle sensor and from reading topic "Sticky: Missfire Boost.." it seems other people have had this problem and was solved by changing the crank angle sensor.

My advice, if it's only just started to happen, get it looked at quickly because it gets worse quick.

i'd change air flow meters over!!

LOL an engine will run without an oxygen sensor signal (though not as economically) so there is no way that would fix a stalling problem.

A missfire is not the same as what your saying you have. So i wouldnt go on anything said in the missfire thread. A common oversight people seem to have is if they have the same symptoms as another person thay automatically think its the same fault! Never assume this as 90% of the time it wont help you.

Deren

LOL an engine will run without an oxygen sensor signal (though not as economically) so there is no way that would fix a stalling problem.

A missfire is not the same as what your saying you have. So i wouldnt go on anything said in the missfire thread. A common oversight people seem to have is if they have the same symptoms as another person thay automatically think its the same fault! Never assume this as 90% of the time it wont help you.

Deren

Car was originally missfiring as well and revs dropping significantly while in motion. Now I just need to work on the stalling problem. I am also running .95 - 1.02 bar. I will check the coils but I would be very appreciative if anyone has any ideas.

Thanks guys! Changed airflow meters over and so far running like a dream and better than before. I had taken this car to the mechanics 3 times before they finally said it was the AFM.

I do not recommend anyone going to Sumo Performance in Nunawading, Vic (Kamikaze's mechanics) as they had the car for over 4 weeks and couldn't nail the problem. I posted my problem here and got a response same day which was accurate and correct. Thanks again to all.

Hi everybody, thanks for the help. i took the plug out of my afm, resoldered it and car goes like a dream. I too thought it was the crank angle sensor, but had the same symptoms of stalling and funny idle. I replaced all the coils and plugs but it would just cut all power for a few seconds and then come good again. instead of changing the afm, pull the plug off, unscrew the plug body on the afm and prise off the top cover. resolder the 5? joints and reglue on top cover and screw housing back in, worked fine for me and cost nuthin.

Thanks.

Hi everybody, thanks for the help. i took the plug out of my afm, resoldered it and car goes like a dream. I too thought it was the crank angle sensor, but had the same symptoms of stalling and funny idle. I replaced all the coils and plugs but it would just cut all power for a few seconds and then come good again. instead of changing the afm, pull the plug off, unscrew the plug body on the afm and prise off the top cover. resolder the 5? joints and reglue on top cover and screw housing back in, worked fine for me and cost nuthin.

Thanks.

Sounds like we may have had very similar problems. My wiring harness had already been fixed, plugged my AFM into another car and found it to be no good.

I found through a bit of searching on sau that cars with pods seem to have the afm break quite frequently due to vibration. when i removed my plug, the solder joints were not even joining, so much so that i just pulled the plug out of the afm. Its a bit fiddly to get that silicon off the afm, but its cheap and easy. ive since realised that is why my car has been running horribly for months. If you do a search on air flow meters you will turn up something helpful.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...