Jump to content
SAU Community

Recommended Posts

as the title suggests i would like some advice on what revs is best to cut a sub 2 second 60 footer. im running gt3040 600hp turbo making 346rwkws on dyno dynamics i willpost dyno sheet. if im making full boost by 4500rpm and i have a good clutch, 245/45x17 nitto extreme drag radials. what is the best tyre pressure to get good traction ie: a good 60 footer as well as what revs so i dont bog the car down e.t.c.also wheres is the best revs to shift for maximum acceleration. anyone in the know would be greatly appreciated. its hard to practise at calder my local track seing how it takes 4 hours to get 5 or 6 runs and by the time you queue for the nxt run youve forgotten what you did the last time you ran,as to try and improve . obviously its illegal to practise on the street ,so i figure if i can go away from these forums with some insight i might have a good chance of nailing a good pass in the limited ammount of runs that one gets at a busy drag strip like calder park. cheers carl.post-6176-1168507421.jpg

Each car is different in its setup.

Your really just going to have to give it a shot, and practice will sort it out for you with regards to the launches.

Tyre pressure, im not sure there.

Gears... I'd be changing as close to your peak power as you can.

If you feel it "drops" a bit on a gear change, just take it a few 100 RPM further the next time till it feels like you shift and it goes back into a meaty area.

Thats how i used to drag mine and it seemed to work ok when i ran a 12.1 even if it was all over the place at the time.

Although, if you get to calder as soon as it opens, and dont muck around, you'll eaily get 10+ runs on a night.

I used to get there early, and you can do back-to-back runs virtually for the first hour and a half before the main rush beings :)

There will be more useful info for sure, that'll just get it started

Good luck with it, you should be hitting 125mph without much of an issue

You need to balance the clutch and throttle. Use at least 4000-5000rpm and lift the clutch and as you do, use more throttle. Dont dump the clutch at high revs as this causes wheelspin. Do it progessively and you feel the tyres bight and then your away. If you are finding that you are getting alot of grip, try it quicker and use more revs until you find out your traction limits. Best i got was 1.88 60', anymore revs and it would break into wheelspin.

Good luck, 125mph should be possible, but will require a perfect run

thanks for the tips robos, i reckon 12.18 from a hks 2535 is pretty darn good! 1.88 sec 60 ft not bad either. i was flicking through the for sale classifieds the other day and iam quite sure that i saw your ad to sell that turbo. what turbo set up are you looking at running next?

thanks for the tips robos, i reckon 12.18 from a hks 2535 is pretty darn good! 1.88 sec 60 ft not bad either. i was flicking through the for sale classifieds the other day and iam quite sure that i saw your ad to sell that turbo. what turbo set up are you looking at running next?

BigCarl

Picked up a GT3071R for a decent price so i thought i would try it. Finally its all on now but having some lack of boost problems so im trying to iron it out.

If you run a decent 60', you should have a 11 in the bag. Just dont get carried away on the take off as thats where it all counts for a good 1/4.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...