Jump to content
SAU Community

Recommended Posts

as the title suggests i would like some advice on what revs is best to cut a sub 2 second 60 footer. im running gt3040 600hp turbo making 346rwkws on dyno dynamics i willpost dyno sheet. if im making full boost by 4500rpm and i have a good clutch, 245/45x17 nitto extreme drag radials. what is the best tyre pressure to get good traction ie: a good 60 footer as well as what revs so i dont bog the car down e.t.c.also wheres is the best revs to shift for maximum acceleration. anyone in the know would be greatly appreciated. its hard to practise at calder my local track seing how it takes 4 hours to get 5 or 6 runs and by the time you queue for the nxt run youve forgotten what you did the last time you ran,as to try and improve . obviously its illegal to practise on the street ,so i figure if i can go away from these forums with some insight i might have a good chance of nailing a good pass in the limited ammount of runs that one gets at a busy drag strip like calder park. cheers carl.post-6176-1168507421.jpg

Each car is different in its setup.

Your really just going to have to give it a shot, and practice will sort it out for you with regards to the launches.

Tyre pressure, im not sure there.

Gears... I'd be changing as close to your peak power as you can.

If you feel it "drops" a bit on a gear change, just take it a few 100 RPM further the next time till it feels like you shift and it goes back into a meaty area.

Thats how i used to drag mine and it seemed to work ok when i ran a 12.1 even if it was all over the place at the time.

Although, if you get to calder as soon as it opens, and dont muck around, you'll eaily get 10+ runs on a night.

I used to get there early, and you can do back-to-back runs virtually for the first hour and a half before the main rush beings :)

There will be more useful info for sure, that'll just get it started

Good luck with it, you should be hitting 125mph without much of an issue

You need to balance the clutch and throttle. Use at least 4000-5000rpm and lift the clutch and as you do, use more throttle. Dont dump the clutch at high revs as this causes wheelspin. Do it progessively and you feel the tyres bight and then your away. If you are finding that you are getting alot of grip, try it quicker and use more revs until you find out your traction limits. Best i got was 1.88 60', anymore revs and it would break into wheelspin.

Good luck, 125mph should be possible, but will require a perfect run

thanks for the tips robos, i reckon 12.18 from a hks 2535 is pretty darn good! 1.88 sec 60 ft not bad either. i was flicking through the for sale classifieds the other day and iam quite sure that i saw your ad to sell that turbo. what turbo set up are you looking at running next?

thanks for the tips robos, i reckon 12.18 from a hks 2535 is pretty darn good! 1.88 sec 60 ft not bad either. i was flicking through the for sale classifieds the other day and iam quite sure that i saw your ad to sell that turbo. what turbo set up are you looking at running next?

BigCarl

Picked up a GT3071R for a decent price so i thought i would try it. Finally its all on now but having some lack of boost problems so im trying to iron it out.

If you run a decent 60', you should have a 11 in the bag. Just dont get carried away on the take off as thats where it all counts for a good 1/4.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
    • You talking about the ones in the photo above? I guess that could make sense. Fixed (but flexible) line from the point up above down to the hubcap thingo, with a rotating air seal thingo. Then fixed (but also still likely flexible) line from the "other side" of the transfer in the hub cap thingo up to the valve stem on the rim. A horrible cludge, but something that could be done. I'd bet on the Unimog version being fed through from the back, as part of the axle assembly, without the need for the vulnerable lines out to the sides. It's amazing what you can do when you have an idea that is not quite impossible. Nearly impossible, but not quite.
×
×
  • Create New...