Jump to content
SAU Community

Whats Going On ? Melbourne Out Of Power?


Recommended Posts

I was stuck in my office for 20 minutes because all our doors are electrically operated and i forgot about emergency exits. Took me about 10 minutes to work up the balls to cross from some offroad near the corner hotel, across 8 lanes and onto hoddle, scary shit..

power was out in endeavour hills but not in dande north. bro was at home alone and doesnt have a clue bout anything. so when power goes off he calls dad. now when you put my dad and bro together 2+2 usually makes 3.

bro ends up playing around with the mains switches at home under instruction from dad over the phone. didnt work so he was told to put it bak to what it was

anyway i got home, and power was still out, so no air con. after 30 mins i call mum in dande, she says she called a friend of hers and confirms power is still out in the 'hills. now about 6.30 and im literally dripping.

finally got fed up and went to check the mains switches. what do i see but all the switches turned off and even some of the fuses just lying around!! simple replacement and sweet air con was mine to enjoy.

the idiocy of my family amazes me

/rant

power was out in endeavour hills but not in dande north. bro was at home alone and doesnt have a clue bout anything. so when power goes off he calls dad. now when you put my dad and bro together 2+2 usually makes 3.

bro ends up playing around with the mains switches at home under instruction from dad over the phone. didnt work so he was told to put it bak to what it was

anyway i got home, and power was still out, so no air con. after 30 mins i call mum in dande, she says she called a friend of hers and confirms power is still out in the 'hills. now about 6.30 and im literally dripping.

finally got fed up and went to check the mains switches. what do i see but all the switches turned off and even some of the fuses just lying around!! simple replacement and sweet air con was mine to enjoy.

the idiocy of my family amazes me

/rant

dunno what u were doing but we dont have ripple control in Vic so there is no remote switching of controled load such as hot water and air con, if the fuses were out, some1 took them ok.

In the not to distant future the use of controled loads such as Air Con wil come at a price on these days. Both the elec distribution and retail companies buy electricty at varying prices every 30min according to demand..I had a quick look at the demand price per MWh yesterday and it went though the roof. However the real issue was that one of the interstate suppies used for meet peak demand requirements was taken off line due to the bushfires...

So what can u expect in the future?

Currently u will be on a fixed tariff setup either flat rate or peak off/peak for fixed times during the day. The new systems to be deployed by 2008 will allow more felxability and in reality help these companies make you, the customer, pay for these peak demand times by varying tarriff rates for controlled load especially...in fact you the customer will probably have visability of this and depending on what u signed up for, might even have ur load shed automatically in these situtaions.

In additiont he distribution companies in your area i.e. AGL, SPAusnet, Cipower/POwercore will have the ability to shed you power and esp. controlled loads such as air con remotely under peak times under the banner of network safety. It comming,...just like water saving, the old days are going to end soon.

In the not to distant future the use of controled loads such as Air Con wil come at a price on these days. Both the elec distribution and retail companies buy electricty at varying prices every 30min according to demand..I had a quick look at the demand price per MWh yesterday and it went though the roof. However the real issue was that one of the interstate suppies used for meet peak demand requirements was taken off line due to the bushfires...

can anyone say ENRON?

Windsor was good :)

And so was my work (Collins St)

aircon all round :yes:

Yes it was... Footscray power came back at 6pm and my work at Collins st was as cold as ice, i was wearing a jacket in my office. LoL

In the not to distant future the use of controled loads such as Air Con wil come at a price on these days. Both the elec distribution and retail companies buy electricty at varying prices every 30min according to demand..I had a quick look at the demand price per MWh yesterday and it went though the roof. However the real issue was that one of the interstate suppies used for meet peak demand requirements was taken off line due to the bushfires...

So what can u expect in the future?

Currently u will be on a fixed tariff setup either flat rate or peak off/peak for fixed times during the day. The new systems to be deployed by 2008 will allow more felxability and in reality help these companies make you, the customer, pay for these peak demand times by varying tarriff rates for controlled load especially...in fact you the customer will probably have visability of this and depending on what u signed up for, might even have ur load shed automatically in these situtaions.

In additiont he distribution companies in your area i.e. AGL, SPAusnet, Cipower/POwercore will have the ability to shed you power and esp. controlled loads such as air con remotely under peak times under the banner of network safety. It comming,...just like water saving, the old days are going to end soon.

I work for Powecor and this is the first I've heard of it? 2008 is very soon to get a system like that underway. Maybe only in small areas as a trial. In the late 80's and 90's there were a few zone substations around melboure that had UFA which stands for Urban Feeder Automation where they could control hot water services coming on and off by sending high frequency signals into the powerlines. Anyway, it's all pretty much all been pulled out because it failed dismally. I think one of the problems with the system was that distribution transformers would trap the high frequencies if there were Delta windings. If it's a direct line with no circuit breakers and windings then it's ok like PLC (Powerline carrier) which is used in SPAusnets transmission lines for intertripping. It works very effectively but on the lower scale for every house it's a big job! At the moment I think load shedding will remain how it is and how it worked yesterday, just rotating who is off for how long to reduce the load.

The problem yesterday is that the 330kV feed from the Snowy scheme (NSW) between Dederang Terminal Station and South Morang Terminal Station tripped off because of the fires and they had to wait until CFA would allow them to fix it. Apparently we get up to 30% of our power from snowy on heavily loaded days like yesterday and with that gone... we had to load shed! I do agree that it will probably happen but I don't think it will be that soon.

I thought the power was bought in 5 min intervals?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 馃槢   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
    • Oh nah, S55 doesn't eat bearings, just the crank hub slips lol.
    • When鈥檚 the tow ball on the 33 coming? 馃檭
    • I welcome any basic question that can help haha. Yes it has 2 unis but the driveshaft is a one piece and the unis are welded without a slip yoke at each end.   What's funny is anytime I've ever had wheel vibrations it's always been in the front so I automatically assume it will lead to steering wheel shake and not chassis vibration. With that being said, I never considered looking at my rear wheel balance... I have doubts though as this wasn't an issue before I pulled the motor and trans but is still very much worth a look. I'll do that tonight after work. Thanks. 
  • Create New...