Jump to content
SAU Community

Recommended Posts

My r33 gtst has a slight backfire when i back off the gas followed by a gargle, all coming from the exhaust. I have only had the car a week and it has always done it since then but i have put some injector cleaner in the fuel and it seems to now be worse. Is this normal for a skyline to be doing this?

Link to comment
https://www.sau.com.au/forums/topic/15218-backfiring/
Share on other sites

I haven't seen a Skyline that doesn't do it :D

Edit: Oh, if it blows lots of black smoke, this too is normal and nothing to worry about. I met someone who drives a turbo Audi and he thought that all Skyline engines were in sh*thouse condition because of all the smoke he sees them blow, I had to educate him that it was just unburnt fuel because of running hella rich.

Link to comment
https://www.sau.com.au/forums/topic/15218-backfiring/#findComment-313371
Share on other sites

Hehe, speaking of scaring pedestrians, I once scared the shite out of some bogun fat chick in my old XY Falcon with worked 302 Windsor and no mufflers. A bunch of boguns decided to meander across the carpark in front of me doing 5kph. It wasn't a pedestrian crossing, so I got a bit pissed off especially since they were in single file and walking slowly.

When the last one (fat chick) was right in the middle of my car, I floored the accelerator and slipped the clutch a little to inch forwards about 5 cm. She just about shit her pants :O

Don't think I can get the same effect happening again with the 'line :P Well, maybe if I moved forwards 1 metre instead of 5cm :P

Link to comment
https://www.sau.com.au/forums/topic/15218-backfiring/#findComment-313626
Share on other sites

  • 5 weeks later...

I drive a Turbo Audi - but im not that guy :P

'line engines are pretty awesome actually, i almost got one, but they got too common.

I know of one Audi A4 Turbo Quattro that blow a lot of smoke - but he has over 220kw at all four. So its a bit extreme. PS. watch out for him. :P

Link to comment
https://www.sau.com.au/forums/topic/15218-backfiring/#findComment-361693
Share on other sites

Does it sound angry? Yes? Then good! Mine consistanly backfires in 1st, 2nd and 3rd gear changes and often if i back off from higher up in the rev rang,Lovin it. The rumble under compression is a nice sound also. It can be controlled with longer slower gear shifts.I must admit a good Ffowing exhaust and rich fuel mixture increases this, and no cat! Oh did I say no cat? Thats illegal isn't it?? LOL

You don't want to much though as that can be cop bait...

RJB.

Link to comment
https://www.sau.com.au/forums/topic/15218-backfiring/#findComment-361879
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • On the compressor side it looks like the best, if your head setup will support doing 100-110lb/min at 30psi-ish boost.   The G45-1350 compressor looks ideally better if you need closer to 40psi for it, given both the G40 1150 and G42 1200 look like they'll be around the 100lb/min mark at 35psi and dropping from there.   Bear in mind the turbine sides are all different between those three turbos, so that COULD be an influencing factor for how they all perform in the real world as well.   Not sure if you've made a conscious decision to only look at Garrett or not, but at least on paper the XRE7169S matches or beats those other three at everything from 30psi up and just going from wheel size alone likely to be at least as responsive as the G40 1150 and seem to behave closer to G42s in terms of turbine flow.
    • @Lithium  looking for a turbo for my Rb30. Want to make sure I understand this correctly.   If I want to stay 40psi or under my best choice of these 3 is actually the smaller G40-1150 ?
    • Massive ups for MTHire also. Could not have done the subframe bushings job without hiring the tool from them. Process was super easy and cost me around 25% of the cost of the tool. If you need a tool to do a one-time job, check them out. (Paid for the rental myself, no sponsorship here.)  
    • I'd suggest calling Unigroup, they have a lot of experience with these, access to reliable fabricators etc. Of course it will cost but at least you can trust what they tell you
×
×
  • Create New...