Jump to content
SAU Community

Dodgy headlight S1 R33

JimX

By JimX,
in General Maintenance

 Share

Recommended Posts

JimX Grand Master

JimX

Posted
Posted

My left highbeam points straight into the ground, even on its highest setting. On the lowest setting it just points even more into the ground (2 metres in front of the car instead of 5 I guess). All the other beams are spot-on, it's just this one that doesn't do what it's told.

I had a fiddle around with the bulb and I could aim it correctly if I held it at a funny angle, so it's possible that something's wrong with the mounting mechanism. It's very hard to work around there without pulling the whole light out, so I think I'll do that next weekend.

Just wondering if anyone else has had a bad headlight aim problem like this before and what the cause might be? Luckily the right high beam illuminates enough on dark roads to get by, but it is damned annoying having no left high beam!

Link to comment
https://www.sau.com.au/forums/topic/15291-dodgy-headlight-s1-r33/
Share on other sites
Ronin 09 Grand Master

Ronin 09

Posted
Posted

JimX, my right h/light was screwed - the light pattern was all over the place. I actually changed the globe and it was much better. They also seem to be really sensitive to getting the globe in properly. For 5 bucks a new globe is worth a shot rather than new light? Hope that helps.

JimX Grand Master

JimX

Posted
  • Author
Posted

Ronin 09, good idea. I was looking at replacing the bulbs with whiter/bluer ones soon anyway (not actually tinted blue, blergh!) so I might do a bulb swap with one that I know is good to see if it's the bulb itself throwing the alignment out.

JimX Grand Master

JimX

Posted
  • Author
Posted

Woohoo! Thanks to the advice of Ronin 09 I managed to fix it without removing the headlight assembly OR resorting to the hammer :)

I took both globes out, put the highbeam one in the lowbeam socket. For some reason the light was now shining higher up than in the highbeam socket. Very weird indeed because I would have expected it to be lower if anything. So I adjusted it to the correct height and left it in there.

I then put the low beam globe in the high beam socket and it also shone higher. But now I could adjust it to normal height. So it's all good now. Very weird all over!

I'm still going to look at getting new blue/white globes, but now I'll know that if I can't get the alignment right I'll try re-mounting them and/or swapping them around a bit.

Ronin 09 Grand Master

Ronin 09

Posted
Posted

Great to hear it, JimX. My high beam still points prettu high, but thats ok because it doesn't dazzle anyone. Lemme know how you go with the globes; i recommended Bosch Silver Evolution globes in another thread - thats what i have. They give off an almost perfectly white light, with a very very slight tinge of purple at certain angles. The only reason why i would like to hear what you use (and how they look) is because these globes were about $150 from sonic racing before they closed down... although i got them from Hong Kong for like a third of the price.

I want to change my high beams, so keep us posted :)

PuppaDuck Collaborator

PuppaDuck

Posted
Posted

I know what you mean...had my lights adjusted to standard height...not long after I try to take some of the bulbs out to get the part number so I could consider getting the white globes...

and somehow when I put one of the bulbs back in, it shines at a different angle...

I just assumed that the bulb isn't sitting in its seat flat enough...

will adjust it this weekend and let you know...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      So, I've been a little busy on this car. I replaced the bonnet struts which is always satisfying but very confusing that nobody else on the planet seems to do this. Its just my routine first thing I do on any car I buy. The boot struts for both the tailgate and the separately opening glass window was a bastard. And, I found a fair bit of rust in the strut cavity. I filled it with rust converter and cleaned up as much of the dirt as I could. There was so much dirt. One piece of the trim was barely hanging on and so I've left it off. I'll try to get a replacement. You can see how disgusting and dirty it all was in this thread; I had to remove the little clips that hold the struts on the ball. The ones I took off had no clips and it was impossible to get them on with them in place. Fingers crossed they stay put. So, I turned my attention to the headlights, they were in a bad way and likely would stop rego. I took the headlights out and found the adjusters were all just loose. So, I fixed those and unclipped the lenses to clean them up. Couldn't believe how easy it was to take all this apart compared to the E90.   I also cleaned up the stockies which was awesome, these are super cool with lug nut covers. They're in good nic but the tyres are shot. I was going to use these for rego but in the end got a fresh pair of rubber for the 17's on the front of the car instead. The front bar of this car is from a late(r) model one. I don't think it's quite LCI but who knows. I'll need to find out. Anyway, the bar was missing the fog lights and the wiring and plugs were for the original ones so I got new plugs and some cheap fogs. I wasn't sure if missing original equipment would hamper my blue slip attempts. Had a couple of these little fellas helping out. But not Ben who got stuck behind the pool heater .... How embarressment.  I ordered new speed sensors for all corners because I knew one was out. I just got cheapies and will replace them with Bosch items when I can find Bosch items. Again, this was just for rego. Alas, it seems the blue speed sensors are not the same as the grey ones. Back they went and replacements ordered. In the end, with my new scan tool, it was just rear left that was shot. Replaced it and cleared the codes. All good now. Lastly, my aux (thermo) fan is being a bit odd. Its powering up at strange times and NOT powering up when I think it should (100C). While this can be caused by a few things, the most likely (for me) is the ambient temp sensor. Given mine reads -40.0C regardless of the temp, I figured it would be good to replace it. In the end, the sensor wiring was abysmal with (terrible) attempts made by somebody to fix it.   I fixed this all up but the sensor is only attached using pins into the wires. The plug is not there. Despite trying and trying to connect it securely it wouldn't work so a replacement sensor and plug is on the way. Oh, I also ordered a replacement piece of trim for the part missing here at the bottom. Ordered from Latvia for $70 delivered. I took a bit of a leap of faith because I didn't have the exact part number and, as usual, there were eleventy billion pieces of trim that looked to fit. Nailed it. Well, its not totally perfect but I think its more a 28 y/o car problem than a trim problem. And, as of today ..... I have bought the workshop manuals 2nd hand off a guy in tassie. 1000+ pages of E39 goodness, hopefully it helps me with the fan. I also have a new temp switch on the way incase its the problem. Stoked.
    • joshuaho96
      R32 GTR - Where to begin

      By joshuaho96 · Posted

      I don't even know that you want an M2 Competition as a track car. My rule for a track car is only risk as much as you're willing to completely total out. Clean stock C5 Z06 Corvettes out here are cheap. Buying someone else's already ruined track car is even cheaper. Maybe I'm just not that good a driver but even a Fiesta ST on the Nordschleife felt like as much car as I could realistically handle.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I've already gone over the cam. A new one is going in. An old one is coming out! The new one is smaller, with less overlap. It has way more lift, but it will be more mild mannered (hopefully, probably very minorly) I'm also measuring for two more mufflers, with the goal of having four mufflers in my car. But that probably will be done by an exhaust shop in a drive in, measure, buy parts, install parts later kind of deal.
    • GTSBoy
      R32 GTR - Where to begin

      By GTSBoy · Posted

      Mine is not even a GTR and I've been resisting the urge to make it a power monster for the last 25 years. And as a consequence, I have driven it to work nearly every day across that span of time.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Since the motor is out, I suggest pop in a nice dirty LS chop cam. MOAR of this please:  
×
×
  • Create New...