Jump to content
SAU Community

Recommended Posts

Hey guys,

Have had trouble starting my car only sometimes lately. Today it took me about 10 turns of the switch to get the starter motor to turn over the engne.

I get in the car, put the key in, turn it past accessories to the 'ON' position I guess, let the fuel pump go for about 5 seconds before turning the key to 'START' and nothing.... just cuts out the radio. Tried it about 7 times, then took the key out, turned it around, did the same thing, did the same thing first attempt, and then on 2nd attempt fired straight away.

Has this happened to anyone else? And what could be the causes?

Worn out ingition barrel not contacting anymore (I have no idea how it works inside the barrel)?

Starter motor contacts bad??

It used to only do it maybe once or twice at most, and only usually every 5 or so times of starting the car (it would usually strart straight away), but yesterday afternoon and today afternoon I had trouble.

Any other ideas?

Thanks,

Fixxxer

Link to comment
https://www.sau.com.au/forums/topic/153238-starting-problems/
Share on other sites

If the key goes in and turns to start normally the first time before flipping it then its got nothing to do with the key or barrel. However commodores use an anti theft device in the key head that flipping the key sometimes helps, but thank god you dont have a commonwhore!

Most likely a starter problem. To be safe you should get a multi meter and load test the battery. First unplug the ignitor so the car wont start. Attached the two terminals of the multimeter to the battery terminals then get someone to try cranking the engine and while its winding over watch the reading on the multimeter. If it drops below 10 volts then your battery is dieing. If not and it stays around 11-12 volts the battery should be fine and you can be more sure its the starter/solinoid causing the fault.

Battery should be fine, its a good battery, I replaced it only about 3 months ago....

It's not like the starter is struggling to start the car, it's like the power is not getting to the starter, and then suddenly i turn the key the right way or something and it fires instantly.

Fixxxer

OK then we can rule out the battery, good. Next look at the starter & solinoid (which are combined) and earthing of the circuit. If there isnt a good earth (strap) you may aswell be not supplying enough power as its the same end result.

Deren

I had the very same problem on my car some time ago!

It ended up beeing the front + and -poles on the left side of the engine bay.

The thing was that the prior owner had connected front-lights to the +pole and that created a gap big enough for dirt getting in and ruin the connection.

Apperently the connection was good enough for panellights and such, but not good enough for the starter.

If i recall correctly i think the windows wouldnt move either...

Hope that helps!

As the brushes wear in a starter you will get an inconsistent starting patterns. But I have also seen a brand new battery off the shelf that I have had to fit to a customers car and it has had a brake in between the cells.

Do what Deren said by checking battery voltage, whilst cranking - this will give you the best indication, also check you main battery lead going to the starter - if these look ok - its time to pull the starter out, and give it to some mug they call an auto electrician :P.

Cheers

Sumo

Ok I will look around the starter motor and see if there is anything wrong with connections.

Next I'll check the battery and connections to the battery, but like I said this doesn't seem to be a problem as there is plenty of kick to start the car when the starter works, and this has been a problem ever since I got the car a year and a half ago (with a different battery).

Fixxxer

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
×
×
  • Create New...