Jump to content
SAU Community

Recommended Posts

Hey guys,

Have had trouble starting my car only sometimes lately. Today it took me about 10 turns of the switch to get the starter motor to turn over the engne.

I get in the car, put the key in, turn it past accessories to the 'ON' position I guess, let the fuel pump go for about 5 seconds before turning the key to 'START' and nothing.... just cuts out the radio. Tried it about 7 times, then took the key out, turned it around, did the same thing, did the same thing first attempt, and then on 2nd attempt fired straight away.

Has this happened to anyone else? And what could be the causes?

Worn out ingition barrel not contacting anymore (I have no idea how it works inside the barrel)?

Starter motor contacts bad??

It used to only do it maybe once or twice at most, and only usually every 5 or so times of starting the car (it would usually strart straight away), but yesterday afternoon and today afternoon I had trouble.

Any other ideas?

Thanks,

Fixxxer

Link to comment
https://www.sau.com.au/forums/topic/153238-starting-problems/
Share on other sites

If the key goes in and turns to start normally the first time before flipping it then its got nothing to do with the key or barrel. However commodores use an anti theft device in the key head that flipping the key sometimes helps, but thank god you dont have a commonwhore!

Most likely a starter problem. To be safe you should get a multi meter and load test the battery. First unplug the ignitor so the car wont start. Attached the two terminals of the multimeter to the battery terminals then get someone to try cranking the engine and while its winding over watch the reading on the multimeter. If it drops below 10 volts then your battery is dieing. If not and it stays around 11-12 volts the battery should be fine and you can be more sure its the starter/solinoid causing the fault.

Battery should be fine, its a good battery, I replaced it only about 3 months ago....

It's not like the starter is struggling to start the car, it's like the power is not getting to the starter, and then suddenly i turn the key the right way or something and it fires instantly.

Fixxxer

OK then we can rule out the battery, good. Next look at the starter & solinoid (which are combined) and earthing of the circuit. If there isnt a good earth (strap) you may aswell be not supplying enough power as its the same end result.

Deren

I had the very same problem on my car some time ago!

It ended up beeing the front + and -poles on the left side of the engine bay.

The thing was that the prior owner had connected front-lights to the +pole and that created a gap big enough for dirt getting in and ruin the connection.

Apperently the connection was good enough for panellights and such, but not good enough for the starter.

If i recall correctly i think the windows wouldnt move either...

Hope that helps!

As the brushes wear in a starter you will get an inconsistent starting patterns. But I have also seen a brand new battery off the shelf that I have had to fit to a customers car and it has had a brake in between the cells.

Do what Deren said by checking battery voltage, whilst cranking - this will give you the best indication, also check you main battery lead going to the starter - if these look ok - its time to pull the starter out, and give it to some mug they call an auto electrician :P.

Cheers

Sumo

Ok I will look around the starter motor and see if there is anything wrong with connections.

Next I'll check the battery and connections to the battery, but like I said this doesn't seem to be a problem as there is plenty of kick to start the car when the starter works, and this has been a problem ever since I got the car a year and a half ago (with a different battery).

Fixxxer

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Don't do it if your gearbox box has already having syncro issues. The short hifter will put a greater load on them. If you must I remember Nismo did a shorter shifter, with the top part being physically shorter and the part that went into the gearbox was the same as stock. In saying that I've had a C's short shifter (I think) in mine for many years, which was given to me as the previous owner was not sympathetic to the gearbox. Thus forwarned I was careful and had to modify my normal changing style. You have to be super accurate with your clutch and shifts
    • Well, after a week of daily driving and having to crawl out between the wheel and the side intrusion bars. I got myself a quick release setup. I went with an NRG short hub and Quick Release with some cute heart cutouts on the pull tabs. Nice and matchy matchy with the rest of the interior accents I have going on.  The only downside is the total stack height even with the short adapter is longer than the old HKB boss kit. Luckily I had some adjustment left on the column so move the wheel away.
    • stock shifter with new bushes, springs and cup will improve it. Gktech do all the bits. The opinion as the years have gone on is the redline is not great in old gearboxes.
    • Hi all   what short shifter do you use on your skykine r34?   my synchronous does have a problem and i was getting huge delay and grinding sound between 2nd and 3rd, did put shockproof red heavy stuff and it is great now/ no issues   would in your view short shifter screw this up?   people seems to suggest/ use cube short shifter and there is standard and premium. Seen review of premium as much better and less play. Thoughts?
    • Yeah, there's a bit of a density and friability difference between pebbles and any of those other things. Silicone will definitely float in oil and so will be mobile enough to move around. Although, again, if it is upstream of the filter it really shouldn't go any further. I would only ever worry about silicone when it is in places downstream of the filter. Upstream of the pickup is a whole 'nother matter. We've all seen what that does. I have seen the most abominable crap settled out in industrial gearboxes, trunnion lube systems and the like, without any sign that any of it has touched anything in the machine. Just chilling in the bottom, waiting for the inevitable operator error that causes the whole machine to need to be dismantled for repairs.
×
×
  • Create New...