Jump to content
SAU Community

Recommended Posts

I replace the tie rod ends on our 32 as the boots were split and the grease was seeping out. Easy enough job.

A week later, wheel alignment attempt showed that the tie rod ends on our s1 stagea were rooted on both sides.

I spoke to Pedders where I bought the set for the 32, not having a listing for a stagea, I asked them to check part numbers for r32, r33 and r34 skylines. All were the same part numbers, and matched for s13 & s14 silvia.

I bought these for the stagea, only to find that the originals are noticably taller and slightly bigger in the body.

Has anyone replaced the tie rod ends in a stagea, and have a part number or cross reference?

Am I safe in the expectation that the skyline parts I fitted this morning will be reliable replacements?

Link to comment
https://www.sau.com.au/forums/topic/153516-tie-rod-ends/
Share on other sites

  • 1 month later...
I have been told the same, but mine are not tottally stuffed, but are getting worn, so what did you end up doing Paul?

I put the Skyline ones in.

Have been working well for the last 3 months or so, just drove from adelaide to melbourne and back.

Only observation is that the steering feels eerily light now. Unsure if I should be concerned about this or not.

Link to comment
https://www.sau.com.au/forums/topic/153516-tie-rod-ends/#findComment-2991973
Share on other sites

s13s will fit

z32 outters will fit with skyline inners

they are all the same really, just different diameters and such

i think the r32 may be a little longer or something?

Ive replced my tie rods on my s13 with r32.

Link to comment
https://www.sau.com.au/forums/topic/153516-tie-rod-ends/#findComment-2992331
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Coming home late at night and driving past the police is the only reason i need one haha And yeh, definitley needs a switch to quickly enable it, dont have time to be getting my phone, opening an app, waiting for it to update etc before being able to make the change
    • Because it is financially convenient for them lol. Why wouldn't they want to give you the lowest possible valuation for your car?
    • Yep. @Duncan also shannons they will rip you dry and will be probably limited on how much you can drive. Also keep in mind that you always have to have it garaged with Shannons, with enthusiasts as per their PDS you can have it 2 times per week on the driveway for example. 
    • I had a generic 4" Varex rear box on my old V8, worked a treat for sneaking home late at night, it was as quite as stock when closed The car was "fairly" loud when open as it consisted of 1" 7/8 headers to 3" catted Y pipe, to 4" single, it did have a resonator in the mid pipe and only the Varex out the back I also hard wired in a Varex dash mount switch, as the key fob thing is a pain to use when driving I wouldn't recommend giving the beans when it is closed though as it creates a large restriction in the exhaust  It also can in very handy when pulled over for "random" breath tests or just cruising past the constabulary   
    • Here is the before and after of the scraping/sanding of the IC pads on the tachometer board for the fix mentioned in this thread. And yes it worked fine after. Just a note if you change any components on the board the tach calibration can be wrong showing the wrong idle etc...only problem is once it is installed back in the cluster you can't get to it to adjust...ouch! My fix was to cut out the calibration pot (the blue one) from the board and run it with two wires to the fuse panel under the dash where I could adjust the idle calibration once everything was installed. And yes I soldered everything up again including the half soldered components either side of the IC in my photos                                
×
×
  • Create New...