Jump to content
SAU Community

Recommended Posts

LOL of course I know you need to use Skyline parts - what I meant was whether the balancer has to be from a RB30, RB26 or RB25 or are they all interchangeable?

Keep it simple try not to think too much. :pirate:

I've said use the balancer that is suited to your ancillaries, so do just that. :ph34r:

All pulleys must match and line up. So... use the balancer that is matched to your ancillaries, that would be the balancer that came with the car.

Just to add to Cubes reply, You definitely wana keep it all the same.

VL's used two different Rb30 balancers (year specific/different belts).

I'm sticking with the VL setup -cheaper to replace pwr steer pump etc..

Edited by Alf

lucky, i just bought a sexy rb30 power bond harmonic balancer for my 25/30, lucky it still lines up then- i ditched the a/c tho as the balancer doesnt use it, one less thing to worry about.

my donk will start bein assembled this weekend and over the next couple, just dummied the head/block/plenum/turbo and ex mani up to see how everything lines up (pics below) and everythings sweet except the vvt oil feed which comes real close to the plenum. can anyone see any probs which i have missed??

also i heard that the block needs shaving on the ex side for the mani to fit, however mine was all good, is this normal??

post-23187-1175613466.jpg

post-23187-1175613559.jpg

post-23187-1175613578.jpg

post-23187-1175613728.jpg

It was a new one..however its just been rebuilt by Mr Turbo down the coast...so it should come back stronger and better.

Lucky there.

On the new motor we ran too tighter bearing clearances and the crank started picking up bearing metal and it clogged the oil feed line to the turbo..starved it of oil and bam...ball bearings in the dry sump tank! However that has now been rectified.

Well we plastigauged mains and big ends at 1.5 thou'or .030mm i think it would be if ive calculated that in my head right...rough enough maybe?

Need bigger for race motor with relatively big power, and doesnt get run in....gets built, straight on dyno and then raced.

I've got a RB30 block sitting on the floor infront of my RB25. I'm wondering if I should put a set a cams in it before i do the conversion? Sure you can make good power with the stock items..

But, is it a better option to do the cams and make a fatter power curve, or spend the money somewhere else?

I'm in 2 minds.. but leaning towards something like a pair of step2 HKS.

They will be fitted with adj gears. which I hope to buy very soon.

I want to make a strong power figure, but not so keen to have to pull 8000rpm to make it. Hence the conversion. I'm after about 420ish rear hp. got GT3040r. it should come on strong a bit earlier than the 35.

Am I thinking right?

cheers.

I've got a RB30 block sitting on the floor infront of my RB25. I'm wondering if I should put a set a cams in it before i do the conversion? Sure you can make good power with the stock items..

But, is it a better option to do the cams and make a fatter power curve, or spend the money somewhere else?

I'm in 2 minds.. but leaning towards something like a pair of step2 HKS.

They will be fitted with adj gears. which I hope to buy very soon.

I want to make a strong power figure, but not so keen to have to pull 8000rpm to make it. Hence the conversion. I'm after about 420ish rear hp. got GT3040r. it should come on strong a bit earlier than the 35.

Am I thinking right?

cheers.

the right cams (not sure what they are) will certainly give you more low-mid power. However depends how big a cams u put in, you'll have to check the head and possibly get it machined to clear the lobes. Oh and you may also need heavy duty springs.

Also, it may be worth while spending the extra money and rebuilding the head and getting a light port job.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...