Jump to content
SAU Community

Recommended Posts

A 26/30 will be less laggy then any other rb, if you could buy a "new" rb30e and put a "new" rb25 head on it, and make 160-200rwkw, there is no reason it wouldnt last 300,000 if the tune was ok. Once you want big power, it changes, but only if you start stressing things beyond their capabilities, ther are a couple of 300rwkw rb30det's on here that have lasted longer than 60,000 and showing no signs of distress. If you have 400rwkw and thrash it every day, then it will last as long as an rb25 with the same power.

Consider I bought a previously unopened RB30 bottom end. All stock. Then I got a near new RB26 head, still with stickers on the heads lower surface and had been in plastic for a while with almost no carbon in the combustion chamber. Built with H beam rods and 9:1 comp pistons, without receiving the boost it makes on the twins (basically kept atmo for run in) it makes 160rwkw.

What do stock 25's make? Wait till this baby gets 18psi.......

Lag? I don't think so!

As with any question you might ask without giving enough detail. It depends. Put a V8 Mack truck turbo on and yes it will lag, but the right turbos for the application then it will be lethal.

Consider I bought a previously unopened RB30 bottom end. All stock. Then I got a near new RB26 head, still with stickers on the heads lower surface and had been in plastic for a while with almost no carbon in the combustion chamber. Built with H beam rods and 9:1 comp pistons, without receiving the boost it makes on the twins (basically kept atmo for run in) it makes 160rwkw.

Hi Geoff, do you remember what sort of revs yielded the 160 rwkw?

Cheers

I'm not reading 260 pages worth of stuff, when from what I've read so far of it (about 10-15 pages in) is mainly people going "OMG, that's great, I plan to do that too"

It seems more of an RB30 chatter then a technical guide

yes you just run an external oil feed to the gallery from your OPS feed. T piece from either the ally heat exchanger or from the bunged hole in the block and run it to a newly tapped hole in the front inlet side of the head where you can see a tube like casting running up the head to the inlet camshaft area. Make the fitting thats in the head feeding the gallery to have about the same size hole as the std feed from the rb25 block which i think is something like 1.6mm....but im probably wrong.

Though this is probably the biggest thread in the tech section, it would definetely have the most tech info available. Sometimes the chatter is techinical :thumbsup:

Hi Geoff, do you remember what sort of revs yielded the 160 rwkw?

Cheers

Mark I don't really remember. I just asked him to tune it to start and run at 60, 80 and 100 so I could run it in.

I'll be getting the bov and boost control sorted so I can have the tune redone soon. Should be interesting. Then it's time to throw it back at the track.

BTW I'm on skype, geoff.williams89 if you feel the need to chat sometime.

Hey Geoff

Did you get the cam gears installed ?

I got the 3.5 inch exhaust done last week, just finished installing a new 10mm fuel line, with new outlet on the tank cap today also.

So booking a tune in as soon as Matts available.

Trevor at custom exhaust specialists said I should pick up 20 - 30 rwhp on same boost with the new exhaust as the old 3 inch would have been maxed out. So looking at over 500 rwhp on 18 psi. But I want to tune it until it pings on 100 ron and then back her off a bit.

Will keep you posted.

PS. Hope your gonna blow or turbo the XR8, otherwise you are going to be very disappointed with the NA V8 :-)

No I've been busy since moving into the new place but maybe later this week.

The Falcon will stay pretty stock. If I want jollies that's what the GTR and racecar are for. Never try to make a silk purse from a sows ear. The ute is for towing a boat and racecar and work.

That thing of yours just keeps getting better mate.

Thats right - I forgot about the boat. Now I understand.

No I've been busy since moving into the new place but maybe later this week.

The Falcon will stay pretty stock. If I want jollies that's what the GTR and racecar are for. Never try to make a silk purse from a sows ear. The ute is for towing a boat and racecar and work.

That thing of yours just keeps getting better mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...