Jump to content
SAU Community

Can U Just Swap Over A Gtst And Gts Ecu

unarmed_skyline
 Share

Recommended Posts

666DAN Grand Master

666DAN

Posted
Posted

Sounds like fund-raising bullshit to me. They don't have differing sensors. Check out a circuit diagram.

I ran my old R34 n/a on the GTT ECU...the only issues were TCS sensors and the like, R33's don't have all the extra bullshit and can just be swapped over.

unarmed_skyline Experienced

unarmed_skyline

Posted
  • Author
Posted

yeh i've turboed my na, and having a few teathing issues, my air flow metre shat its self as they are different between the models, and the ecu is really struggling just keeps leaning out the car even with a safc, my cheapest option is if i can just swap to a turbo ecu n use the safc to tune there but if i have to change the wiring which 3 reputable places that say they have done it before say u have to its not going to be cheaper than say going to dr drift and getting the ecu moddifyed or getting a second hand microtech and hard wiring it then tunning it

unarmed_skyline Experienced

unarmed_skyline

Posted
  • Author
Posted

hey been searching everywhere for a pinnout diagrame for an na r33 ecu anyone know where i can find one only found the turbo one and it doesnt help when i want to do a comparison

666DAN Grand Master

666DAN

Posted
Posted
Do you mind if I ask why your swaping a NA to Turbo ECU?

My last car was N/A + turbo...put the turbo ECU in to make things easier...isn't so with the R34's too much missing bullshit throws up the "check engine light"

R33's use all the same sensors, they have the luxury of no Turbo pressure sensor, TCS, Secondary throttle motors etc etc

The AFM's are the same between turbo and N/A just different between series 1 and series 2's

unarmed_skyline Experienced

unarmed_skyline

Posted
  • Author
Posted

the reckers i got my air flow meter from said they are different, the sensor is slightly diff or something and the barcode/part numbers are different, nothing that i could tell the diff between thou

STATUS Grand Master

STATUS

Posted
Posted (edited)

I just fitted a emanage ultimate for a guy who turboed his NA R34 and the pins were the same. Rpm didnt work though, no biggy i just used the cas signal. This might be what bought on 666DAN engine light??

so i cant imagine why NA 33 would be differrent.

Edited by URAS
666DAN Grand Master

666DAN

Posted
Posted

RPM should work, my one did on the e-manage blue, I can't see them changing it for the ultimate??

No, there is a lot to the R34 ECU's which cause the engine light, I know them backwards unfortunately/fortunately :laugh:

STATUS Grand Master

STATUS

Posted
Posted
RPM should work, my one did on the e-manage blue, I can't see them changing it for the ultimate??

No, there is a lot to the R34 ECU's which cause the engine light, I know them backwards unfortunately/fortunately :laugh:

i have fitted probaly 20 or so to R33 and about 6 to R34 gtt with Zero issues. The R34 NA one did not like the rpm signal though (it read 5340 at idle :laugh: ) so i swapped it to cas sens and it was sweet. I probaly should have investigated the rpm wierdness but it was not needed.

666DAN Grand Master

666DAN

Posted
Posted
i have fitted probaly 20 or so to R33 and about 6 to R34 gtt with Zero issues. The R34 NA one did not like the rpm signal though (it read 5340 at idle :laugh: ) so i swapped it to cas sens and it was sweet. I probaly should have investigated the rpm wierdness but it was not needed.

Interesting, it must be something the ultimate doesn't like. I wonder what the difference to the blue is???

I know for the 350Z you require the rpm signal adapter, maybe it was a late model using a different CAS?

STATUS Grand Master

STATUS

Posted
Posted
Interesting, it must be something the ultimate doesn't like. I wonder what the difference to the blue is???

I know for the 350Z you require the rpm signal adapter, maybe it was a late model using a different CAS?

yeah late R33 seies two and R34 require the internal ignition signal adapter and jumpe 8 set to 12v instead of 5v.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • sonicii
      Lower A arm Skyline v35

      By sonicii · Posted

      The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...