Jump to content
SAU Community

Recommended Posts

hi guys just wondering iam wanting to rebuild my rb25 just wondering if this will work and what will need to be done to the block.

i want to use rb26 crank to stroke it

then do i need to use 26 pistons and rods or can i use 25 ones

thanks for any help

iam wanting to run a to4z turbo

i was think of using jun internals

Link to comment
https://www.sau.com.au/forums/topic/154689-rb2526/
Share on other sites

Whats your budget dude?

If you use the RB26 crank, rods i think the RB25 pistons.

Someone will confirm as a lot have done it.

I just used the RB25 crank/26 rod/25 piston

it is going into a stagea so i want about 300kw

so i can just use a forged 26 crank rods and pistons

what the deck height will the pistons go to high

Link to comment
https://www.sau.com.au/forums/topic/154689-rb2526/#findComment-2877209
Share on other sites

26 rods and crank and pistons will do it. Same deck height and rod length remember.

25 pistons on 26 rod and crank would be sitting proud of the block at TDC

so BD Dave i can just 26 crank and rods and pistons and i wont have to do anything to the block or

Link to comment
https://www.sau.com.au/forums/topic/154689-rb2526/#findComment-2877409
Share on other sites

26 crank has longer stroke, rods are equal (in size, but 26`s are stronger), pistons are different. block height is the same, head cc is almoust th same (25 a bit smaller)

26 or aftermarket rods is a must as 25 rods are weak.

26 crank + 25 pistons will have CR too high or what BHDave said.

The best option is 26 crank+rods+pistons in 25 block. i do the same thing for myself now.

Link to comment
https://www.sau.com.au/forums/topic/154689-rb2526/#findComment-2877447
Share on other sites

You have to check that there's sufficient clearance in the block for the longer throw crank and the big ends of the rods, so maybe a bit of machining there (some one will have to confirm as i haven't dummied one up to check). As you'd probably put in new pistons anyway it's just a matter of machining the bore to suit the new pistons (assuming .5 oversize).

Link to comment
https://www.sau.com.au/forums/topic/154689-rb2526/#findComment-2878458
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Maybe I also should have wrote that a bit better lol. I did come 8th last in English at school during the HSC, ironically spent 2 decades reading/writing specifications and contracts in IT 😂
    • Right, but that's in-cylinder, there's the interaction between that and the TWC which complicates things. Pulling out timing to reduce NOx is a strategy I saw in transitional emissions vehicles like stuff from 1974 or so. The two inlet runner system is interesting but I'm not sure it makes a huge difference as far as emissions goes, is it a tumble valve? I've seen stuff like that even in cars from the late 80s. 
    • Hello all,   so i recently swapped out my rb20de neo with an rb25de neo( engine,transmission, wiring and the diff everything) but i just cant get the gear indication light on the dash to work when i switch to tiptronic mode. Note there is a steering wheel switch beside the shifter and i dont have that. I did notice yesterday while switching to tiptronic that the indicator on the dash started to work but it didn't afterwards. Does anyone know how this actually works? Or do i still need that steering wheel switch to be connected and on for that gear indicator to work?
    • Hence why I said earlier that I don't think the turbo Neos ever would have actually qualified as an LEV. I suspect the only actual LEVs that came out of Nissan were the NA Neos. Still call them all Neos. They all stil have the Neo-ness. Just that they don't all qualify as as LEVs.
    • It will give gains, but you wont hit 600 It will give gains but it wont get you to 600 imo. You will also sacrifice low down and you will be adding extra volume if you port match it, more so if you port the plenum runners depending and how its done I think the only time youre going to see about 100hp gains is if the car is making well over 1k kw I do have a spare set that I was going to test with, but i dont actually think there is anything worth getting going larger. I did a fair few S14/S15 and the standard TB is fairly small, I went to 60 and in some cases 64mm which is significant over the stock unit. You can also get some weird ratio changes. I think 20kw will be a stretch on a roller dyno. If I had it apart I might mill the shafts a little and not expect much, I think the stock size is still pretty good for a street/track car even with larger capacity. I might change diameter it if its a drag only car
×
×
  • Create New...