Jump to content
SAU Community

Recommended Posts

nah of course not. how could a change in charge temperature, density and oxygen composition possibly change the vehicle emmisions? :)

The change in temperature and density will be measured by the air mass meter(s), and the ECU will use this signal to set injector pulse. If everything's working well it should not affect emissions much, if at all.

Change in oxygen composition? Do you mean change the oxygen content of air? By what process could that occur??

For the original poster - take it to a tuner and ask for an emissions legal tune ;-) You will need to do different things depending on which exhaust gases are too high, so get an emissions check from the RTA to give you a baseline starting point.

Read this thread thru to the end;

http://www.skylinesaustralia.com/forums/in...amp;hl=emission

HTH

Link to comment
https://www.sau.com.au/forums/topic/155803-emissons/#findComment-2903405
Share on other sites

indeed. change anything and you can expect the emissions to get worse - do you think nissan's engineers are idiots?

Not at all. I suspect they have built the system to be emissions legal at many different intake temps.

I made the assumption that a bigger intercooler would be analogous to a lower ambient temperature. I may well be full of crap as i have no first hand experience, but the reasoning behind "change anything and you can expect the emissions to get worse" seems pretty weak. Care to elaborate on why? Is it because the intercooler changes the oxygen composition ;-)

Link to comment
https://www.sau.com.au/forums/topic/155803-emissons/#findComment-2913117
Share on other sites

I guarantee adding an intercooler 4 or 5 times the size of the o.e.m component will change the emissions from the factory recorded specs.

Stating otherwise is just showing your ignorance of the facts :D

Cheers :happy:

if this is true how come, to get a intercooler enginered there's no need to do a emissions test?you think if it changed emissions to much engineers would have to get them passed by the rta??????

Link to comment
https://www.sau.com.au/forums/topic/155803-emissons/#findComment-2913237
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...