Jump to content
SAU Community

Recommended Posts

thats all to technical for me, so for an idiot help me out... why do they check hieght with the wheel on say the front bar? if it relates to axles..

..and yeh im not smart with this technical shit before someone becomes a smartass :)

The axles rule is just the "lowest point"...

Generally a front bar is within the restriction distance so its 100mm.

Usually the only place that can be lower than 100mm (how low depends on the calc's), is usually around where your CAT would finish.

It's a very small section.

Obviously the above is super generic, each situation is different.

Make better sense?

im about to go get my car tested/fixedc. But i am confused and want to know all the information before i fork out my money so...

its an Rb25det, R34. so 90db @4800rpm max legal...

when it was tested it got 89-91db @ that, but bounced up on 'deacceleration'...is that a problem? or am i just being screwed by the system??

i mean if its legal @4800...whats with getting busted when its de-accellarting at some other RPM??

thanks

So after spending hours reading this and other threads, EPA documents and the tealeaves of some long lost Chinese tribe, I'm still totally confused about what you can and cannot do.

From my reading, it seems like basically ANY mod at all is pretty much illegal EPA wise, BUT, in the EPA 06 document it says:

Any modification is permitted provided that it can be

shown, by way of test1 or engineering reason, to

show that the modification would not be expected to

cause an increase in emissions beyond a similar,

unmodified vehicle.

So does that mean with an ADR compliance thing or engineering cert, 'ANY' mod is actually OK?

I'll list some mods/reasons/questions to be more specific:

- Intake manifold/plenum - There are a hundred threads on here about how to modify stock, put in plasmaman/greddy etc, but is any of it actually legal at all?

- POD (dry) is legal, but not with any change to intercooler. But what about those in an airbox, because again, 100 threads about how to do that and questions about that

- FMIC/SMIC, as above really.

- Injectors? EPA says "Extra or larger fuel injectors are not permitted." so not that they could actually tell without pulling them out, but they are still illegal right? So the 100 threads talking about them, all illegal?

- ECU, again says not permitted, unless to meet ADR.

- Turbo changes, doesn't actually talk about that much in terms of changing the size/CFM/PSI etc, just that external wastegate not permitted (and therefore majorly reducing the number of turbos available). Highflowing is impossible to tell, but is it actually legal? What about changing other aspects (impeller size/type, housing, etc) but still keeping an internal wastegate? Again, 500 threads on this, but is any of it legal?

- Exhaust manifold, seems to be all OK to mod this, ie stick in 3" dump pipes, as long as doesn't break any other rules.

- Exhaust cat and back, again legal as long as isn't too noisy, still maintains the same catalytic quality etc?

- Boost controller, probably belongs with ECU, but illegal? How do make use of your fancy new highflow without one?

As I said at the start, it seems all of this CAN be done contrary to all of that document saying NO NOT PERMITTED, so long as ADR/engineering certs are gotten? Is that right?

Basically, at the end of the day, I'm asking, what mods can be done legally, and how do you go about it (actual mod, as well as the legal aspects)

I know 95% of you guys just do it yourself or take to your local mechanic, without even looking at the legality, but a few like R31Nismoid have actually gotten damn close to following the law 100% and still making major power.

As a side point, how do performance shops like Dr Drift, Mercury, etc do modifications that majorly increase the power, ie 300RWKW etc, when all/most of the mods are illegal EPA wise? OR is this not the case because they are legit/engineer approved places? IE, can you have mods done at these places and it is legal?

Edited by Thelen
Totally depends on the year of being made.

As you said Alex - pre 1983 cars have different rules, there are also cars that do not require CAT convertors and so on due to age etc etc.

HOWEVER should you put say a RB26 into a Datto 180b - you would need to comply with the MOTOR's emission requirements, not the cars.

It's very much subjective to the situation - if you can provide more detailed info we could help futher :D

well, i own a s14 which was sold in 1995. so do i have to follow the ridiculous new sounds restrictions (90db) or the restrictions when the car was released? which was probably 96db.

So after spending hours reading this and other threads, EPA documents and the tealeaves of some long lost Chinese tribe, I'm still totally confused about what you can and cannot do.

From my reading, it seems like basically ANY mod at all is pretty much illegal EPA wise, BUT, in the EPA 06 document it says:

Any modification is permitted provided that it can be

shown, by way of test1 or engineering reason, to

show that the modification would not be expected to

cause an increase in emissions beyond a similar,

unmodified vehicle.

So does that mean with an ADR compliance thing or engineering cert, 'ANY' mod is actually OK?

That is more in reference to replacement parts.

ie. injectors non standard or aftermarket AFM, but ALL very close to the factory specifications.

In the event that say Nissan discontinue manufacturing or something.

Engineers certs do not cover all emissions testing in Vic unfortunately, EPA has some grounding.

I'll list some mods/reasons/questions to be more specific:

- Intake manifold/plenum - There are a hundred threads on here about how to modify stock, put in plasmaman/greddy etc, but is any of it actually legal at all?

- POD (dry) is legal, but not with any change to intercooler. But what about those in an airbox, because again, 100 threads about how to do that and questions about that

- FMIC/SMIC, as above really.

- Injectors? EPA says "Extra or larger fuel injectors are not permitted." so not that they could actually tell without pulling them out, but they are still illegal right? So the 100 threads talking about them, all illegal?

- ECU, again says not permitted, unless to meet ADR.

- Turbo changes, doesn't actually talk about that much in terms of changing the size/CFM/PSI etc, just that external wastegate not permitted (and therefore majorly reducing the number of turbos available). Highflowing is impossible to tell, but is it actually legal? What about changing other aspects (impeller size/type, housing, etc) but still keeping an internal wastegate? Again, 500 threads on this, but is any of it legal?

- Exhaust manifold, seems to be all OK to mod this, ie stick in 3" dump pipes, as long as doesn't break any other rules.

- Exhaust cat and back, again legal as long as isn't too noisy, still maintains the same catalytic quality etc?

- Boost controller, probably belongs with ECU, but illegal? How do make use of your fancy new highflow without one?

As I said at the start, it seems all of this CAN be done contrary to all of that document saying NO NOT PERMITTED, so long as ADR/engineering certs are gotten? Is that right?

Basically, at the end of the day, I'm asking, what mods can be done legally, and how do you go about it (actual mod, as well as the legal aspects)

I know 95% of you guys just do it yourself or take to your local mechanic, without even looking at the legality, but a few like R31Nismoid have actually gotten damn close to following the law 100% and still making major power.

As a side point, how do performance shops like Dr Drift, Mercury, etc do modifications that majorly increase the power, ie 300RWKW etc, when all/most of the mods are illegal EPA wise? OR is this not the case because they are legit/engineer approved places? IE, can you have mods done at these places and it is legal?

Most of the answers are in this thread mate...

Plenum - Illegal

POD - Illegal (unless 1 intake mod)

FMIC - Illegal (unless 1 intake mod)

Injectors - Illegal, given you need aftermarket ECU to run them...

ECU - Same as above.

Turbo - Impossible to tell a hi-flow, illegal but cannot be checked. Larger than factory turbos are illegal either way.

Exhaust - Manifold is fine

Exhaust - Could be 5" for all it matters, however MUST be within noise restrictions

Boost control - Illegal. Allows you to increase boost

You can get all the above legal - IF you go through ADR testing and its within limits.

Issue is to get that approval is a $3000 test, and if you fail, you don't get a refund.

OK, as I said the answers are in the thread, I already said/knew that they were illegal, what I was getting at is how it is done legally.

Aside from the $2-3k testing, there really is no way to get EPA legal mods of the above done?

So basically 95% of the posts here are illegal lol? Well, not illegal, but clearly the owner/modifier isn't following any testing or anything :)

I guess just have to live with the risk of fines from EPA to see any/much increase in power without just buying a plain faster car :)

Just spoke to *** at RE customs, and don't quote me or him on it, but he said people just do the mods and if they get done replace with stocks and get it all cleared. Seems a bit ridicules to do this, even more so that EPA isn't more proactive (not that im saying they SHOULD enforce the law more lol, just saying they do a pretty shitty job), but whatever TIA lol.

So looks like I'll just have to suck my balls in and hope they don't get snipped by a cop and sent to teh bad house.

Edited by Thelen

I know this sounds like a small thing.... but best I check...

I've changed the number plate light on my R34 to a white LED (T10). I'm aware any other colour is not allowed.

Is this allowed? Reason I ask is because it doesn't seem as bright as the original (T10) incandesent light.

Plenum - Illegal (unless 1 intake mod)

POD - Illegal (unless 1 intake mod)

FMIC - Illegal (unless 1 intake mod)

Injectors - Illegal, given you need aftermarket ECU to run them...

1 intake mod??

You have this regulation from the EPA modification guidlines wrong if you think you are only allowed 1 intake modification.

You can have as many intake modifications as you like provided they meet the requirements unless you have an aftermarket intercooler which in the case of an aftermarket intercooler it is the only modification that you are allowed to have.

Mofied plenum chambers are not legal under any circumstances without ADR approval.

your post didnt make much sense to me, how can you have more than one if you can only modify the cooler but nothing else thats 1..

if u put a pod u cant have the cooler, and your saying u cant have a plenum regardless so how do u have as many as u like?

1 intake mod??

You have this regulation from the EPA modification guidlines wrong if you think you are only allowed 1 intake modification.

You can have as many intake modifications as you like provided they meet the requirements unless you have an aftermarket intercooler which in the case of an aftermarket intercooler it is the only modification that you are allowed to have.

Mofied plenum chambers are not legal under any circumstances without ADR approval.

:action-smiley-069:

Intercoolers that are larger than standard or have a different mounting location or are added where none were originally fitted, are permitted only if no other changes to the intake system have been made. In other words, you may have a pod filter or modified/added intercooler, but not both. Any sensors integral to the original intercooler or intake system just be retrofitted and be in the correct location.
Modified or aftermarket plenum chambers or throttle bodies are not permitted.

Document is here: EPA Guidelines (2006)

So guess what, given you only have a 1x Airbox, 1x Intercooler, 1x Plenum on pretty much every EFI car... What's left to change exactly? Painting the piping pink?

And you are only allowed to change two of those 3...

On top of that you are only allowed to mod one...

Guess what that leaves us with to do?

You are only allowed to make... 1 intake modification.

Usually the only place that can be lower than 100mm (how low depends on the calc's), is usually around where your CAT would finish.

It's a very small section.

That's so dumb coz that's where speed bumps will rip the exhaust off! Is there a maximum height that speed bumps are allowed to be? haha

I know this sounds like a small thing.... but best I check...

I've changed the number plate light on my R34 to a white LED (T10). I'm aware any other colour is not allowed.

Is this allowed? Reason I ask is because it doesn't seem as bright as the original (T10) incandesent light.

I know there is some sort of ADR around having the plate lit up for the obvious reasons, unsure if the actual amount of light is specified though.

I've never really looked into something that trivial :action-smiley-069:

How far that goes to get you in trouble or not i wouldn't be entirely sure either.

I know you can be defected for one that doesn't work... but given yours works... even if it wasn't inline with the rules totally, should be ok.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The values for HID colour are also defined ~ see https://www.legislation.gov.au/F2006L02732/latest/text  ~ goto section 3.9 onwards ....
    • So, if the headlights' cutoff behaviour (angles, heights, etc) are not as per 6.2.6.1.1 without automatic levelling, then you have to have to have automatic** levelling. Also, if the headlight does not have the required markings, then neither automatic nor manual adjusters are going to be acceptable. That's because the base headlight itself does not meet the minimum requirement (which is the marking). ** with the option of manual levelling, if the headlight otherwise meets the same requirements as for the automatic case AND can be set to the "base" alignment at the headlight itself. So that's an additional requirement for the manual case. So, provided that the marking is on the headlight and there is a local manual adjustment back to "base" on the headlight, then yes, you could argue that they are code compliant. But if you are missing any single one of these things, then they are not. And unlike certain other standards that I work with, there does not seem to be scope to prepare a "fitness for purpose" report. Well, I guess there actually is. You might engage an automotive engineer to write a report stating that the lights meet the performance requirements of the standard even if they are missing, for example, the markings.  
    • Vertical orientation   6.2.6.1.1. The initial downward inclination of the cut off of the dipped-beam to be set in the unladen vehicle state with one person in the driver's seat shall be specified within an accuracy of 0.1 per cent by the manufacturer and indicated in a clearly legible and indelible manner on each vehicle close to either headlamp or the manufacturer's plate by the symbol shown in Annex 7.   The value of this indicated downward inclination shall be defined in accordance with paragraph 6.2.6.1.2.   6.2.6.1.2. Depending on the mounting height in metres (h) of the lower edge of the apparent surface in the direction of the reference axis of the dipped beam headlamp, measured on the unladen vehicles, the vertical inclination of the cut off of the dipped- beam shall, under all the static conditions of Annex 5, remain between the following limits and the initial aiming shall have the following values:   h < 0.8   Limits: between 0.5 per cent and 2.5 per cent   Initial aiming: between 1.0 per cent and 1.5 per cent   0.8 < h < 1.0   Limits: between 0.5 per cent and 2.5 per cent   Initial aiming: between 1.0 per cent and 1.5 per cent   Or, at the discretion of the manufacturer,   Limits: between 1.0 per cent and 3.0 per cent   Initial aiming: between 1.5 per cent and 2.0 per cent   The application for the vehicle type approval shall, in this case, contain information as to which of the two alternatives is to be used.   h > 1.0   Limits: between 1.0 per cent and 3.0 per cent   Initial aiming: between 1.5 per cent and 2.0 per cent   The above limits and the initial aiming values are summarized in the diagram below.   For category N3G (off-road) vehicles where the headlamps exceed a height of 1,200 mm, the limits for the vertical inclination of the cut-off shall be between: -1.5 per cent and -3.5 per cent.   The initial aim shall be set between: -2 per cent and -2.5 per cent.
×
×
  • Create New...