Jump to content
SAU Community

Plenum Install

guesty

By guesty,
in Tasmania

 Share

Recommended Posts

guesty Proficient

guesty

Posted
Posted

just wondering if anybody has fitted a greddy style plenum to their rb25det? Im having a bit of trouble with the hoses. also could somebody please take close up photos on their engine bay of a r33 gtst? If any of you are in Burnie feel free to come up and help out.

Link to comment
Share on other sites
Shane_954 Enthusiast

Shane_954

Posted
Posted (edited)

Hey there,

I fitted a greddy plenum to WHITER33's car, the plenum was a little tricky to fit. I didnt end up fitting the auxilliary air control valve, left it off because his car runs a haltech ecu, was able to use the stepper motor for cold start idle up. On the stepper motor it has 2 hose inlets, one runs to the AAC valve, the other to a position infront of the throttle butterfly in the cooler pipe. I simply ran a hose between the stepper motor and the cooler pipe and blocked off the other end of the stepper motor. We ended up fitting an 85mm hypertune billet throttle body. As for coolant hoses etc, i blocked off the 2 small hoses running to the factory throttle body. The top radiator hose fits, just gotta turn it upsidedown or flip it over, you'll work it out. You will also need lengthen you wiring to the stepper motor. The job wasnt that bad to do, but you will appreciate it more once finished. Makes things alot easier.

Edited by shane_180sx
Link to comment
Share on other sites
Shane_954 Enthusiast

Shane_954

Posted
Posted

They only ran hoses to the stock throttle bodies to prevent the butterfly sticking open in very cold conditions, wouldnt bother with the hassle of running them. Then again i wouldnt bother with the stock one after seeing the difference a decent one can make.

Link to comment
Share on other sites
  • 2 months later...
Jamskate Newbie

Jamskate

Posted
Posted
Hey there,

I fitted a greddy plenum to WHITER33's car, the plenum was a little tricky to fit. I didnt end up fitting the auxilliary air control valve, left it off because his car runs a haltech ecu, was able to use the stepper motor for cold start idle up. On the stepper motor it has 2 hose inlets, one runs to the AAC valve, the other to a position infront of the throttle butterfly in the cooler pipe. I simply ran a hose between the stepper motor and the cooler pipe and blocked off the other end of the stepper motor. We ended up fitting an 85mm hypertune billet throttle body. As for coolant hoses etc, i blocked off the 2 small hoses running to the factory throttle body. The top radiator hose fits, just gotta turn it upsidedown or flip it over, you'll work it out. You will also need lengthen you wiring to the stepper motor. The job wasnt that bad to do, but you will appreciate it more once finished. Makes things alot easier.

Don't suppose you took step by step photo's.. I see tons of threads talking about installing these plenums but no one with a really good step by step.. I sure would love to see an install FAQ with step by step pics.

BTW thanks fo explaining that i don't need the AAC.. I've been trying to figure out where I'm supposed to mount it or if i needed to buy a different type.

Thanks

Jam

Link to comment
Share on other sites
Firefrog Collaborator

Firefrog

Posted
Posted

Sorry to hijack, but I see you took your cam gear cover off, I've thought about taking mine off, but was under the impression that the sensor on the passanger side gear was something important that I shouldn't touch, and would need to be re-aligned properly. Could you clarify if perhaps this is easier to do then I assumed? :blink:

Link to comment
Share on other sites
WHITER33GTS-T Veteran

WHITER33GTS-T

Posted
Posted
Sorry to hijack, but I see you took your cam gear cover off, I've thought about taking mine off, but was under the impression that the sensor on the passanger side gear was something important that I shouldn't touch, and would need to be re-aligned properly. Could you clarify if perhaps this is easier to do then I assumed? :D

I just put a little mark on the CAS and where it bolts onto so i could line it back up again. Easy.

Link to comment
Share on other sites
WHITER33GTS-T Veteran

WHITER33GTS-T

Posted
Posted
WHITER33, Are you keeping the weapon and going with the big stalled auto and NOS?? Come on 10z!! Happy boosting!

Yeah will be keeping this for a little longer now as with the power its making its awesome fun to drive but the 18s dont like the way in comes on boost...

Im looking at a direct port NOS kit at the moment and want to get that installed and setup before i get the auto so i can work out what stally i need. A 3lt bottom end is also still on the cards or i could stroke the 2.5

Link to comment
Share on other sites
guesty Proficient

guesty

Posted
  • Author
Posted

i didn't take step by step photo's either, but am willing to help others fit their plenums. it does start to get a bit tight under the plenum but im so much happier with the overall looks and performance of the engine bay. i can sorce these plenums for around $350 including freight.

Link to comment
Share on other sites
PHaT MR30 Grand Master

PHaT MR30

Posted
Posted
i didn't take step by step photo's either, but am willing to help others fit their plenums. it does start to get a bit tight under the plenum but im so much happier with the overall looks and performance of the engine bay. i can sorce these plenums for around $350 including freight.

If these are those copy ones, are you cleaning out the insides of them? from reports form other members on here there is alot of slag on the inside of them that needs to be ground off (casting defects), other than that they are ok though i think.

Link to comment
Share on other sites
guesty Proficient

guesty

Posted
  • Author
Posted

i didn't clean mine out much. i haven't had my car dyno tuned yet so im not sure what difference they make, but it seems to rev harder and have more torque.

Link to comment
Share on other sites
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DraftySquash
      Red Line 75W90NS in rear diff R34 GTT

      By DraftySquash · Posted

      Hi everyone, I bought the Redline diff oil and the seller has sent me Redline 75W90NS even though that’s not what’s pictured.  I’ve already booked a hoist to go and change my diff tomorrow but I’m not sure if the NS is ok for the rear diff in a R34 GTT I think the NS does not have any slip modifiers so would that be an issue?    thanks in advance 
    • iamhe77
      M35 Stagea intake suction pipe

      By iamhe77 · Posted

      Not easy to find pics from 15 years ago, but here is a partial one. Keep in mind that it curved immediately from the airbox, then kept a straight line for the MAF to read correctly, followed by a 45 degree bend straight down to the turbo. This connection was the most difficult as it had to twist as well as bend to meet the almost vertical straight section of the intake.
    • GTSBoy
      AC Compressor

      By GTSBoy · Posted

      Yes, well, wrt a wheel alignment, there are two types. Either: You have very little added adjustables, in which case the alignment can be done by anyone in any tyre shop or equivalent, and will only take 30 minutes, and so there is no reason to even consider leaving the car there. OR: The alignment is a major exercise because you have adjustables everywhere and so you will need to be taking it to a shop that is skilled and experienced at setting up race cars and the like, and you won't need to worry about leaving the car there.
    • burn4005
      R35 GTR servo and master cylinder conversion

      By burn4005 · Posted

      does anyone know the specs of the R35 master cylinder, rear ratio and knee point? the BM57 is a 0.4 rear ratio with a 435psi knee. I'm looking for someone with a much lower knee pressure. the piston area of the R35 brakes isnt that big so might not work for me but this is interesting.. the other option for me is a GU patrol master cylinder and booster and do the prop valve externally.
    • soviet_merlin
      AC Compressor

      By soviet_merlin · Posted

      It sounds like by avoiding maintenance you may be doing more damage than a hypothetical guy in a workshop taking it for a spin. Not sure if you are just being paranoid or things are actually that bad in the US. Find a reputable shop not run by dickheads. Look for people that take pride in their work. Stick around for the day if you have to
×
×
  • Create New...