Jump to content
SAU Community

Rb30det/tt Vs 2jz

Jago

By Jago,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Warpspeed
Warpspeed

Yes and no. Engineering is all about calculating stress and fatigue limits, and staying within known and reasonable bounds. The guys that design and build bridges and high rise buildings do not bui

bubba Grand Master

bubba

Posted
Posted

Well, I am not a guru but I can tell you straight up a 2JZGTE can handle 600+hp in factory form. An RB26/30 is a purpose built engine and will handle as much as the parts you can afford to put in it.

One of my mates has a mk.4 2jz supra, came from japan pushing 300rwhp and ran a best ET of 12.7 (with slicks).

Another mate has an RB25/30DETT, made 310rwhp @ 10psi but never saw the strip like that. Now makes 494rwhp @ 21psi.

The RB engine at a similar power output felt a bit harsher than the 2JZ but that was probably just turbo combination and the fact that he was only running a rev limit of 5500rpm at that time as it was leaning out.. full boost by 4000rpm and hit the limiter at 5500rpm! Now, I never drove this car with the RB30, only when it had an RB20.

I did however drive the supra around the time the owner ran a 12.7, it felt a hell of a lot smoother and with the sequential turbos starting to boost ~2000rpm, the power delivery felt very linear.

The supra was pretty much factory and the engine came in that car, the RB on the other hand is in a VH commodore.. so it's kinda hard to tell :)

Cubes Grand Master

Cubes

Posted
Posted

300rwhp without sequential turbo's but using only a stock rb25det turbo the rb30det's make all their boost ~2000rpm. So not really a good comparison.

At what power level (not US dyno power levels but here in AUS) do the 2jz's start bending rods?

I've on occasions visited the supraforums and laughed quite hard how they seem to think rb25/26's and 30's melt pistons. lmao.. Poor tuning melts/breaks pistons. :)

My general feeling is the 2JZ is a slightly stronger motor than the RB30. RB30DET's have reasonable bottom ends, they manage to hold close to 400rwkw providing the tune is good. I have no idea what the 2jz is capable of on an AUS dyno.

nizmo_freek Experienced

nizmo_freek

Posted
Posted
as bubba said, factory form 600+ hp as opposed to purpose built rb30det. i have some massive respect for the 2jz. I would even compare a 1jz to a rb26det, as many people do these days.

You dont need a "purpose built" rb30 to make huge power, just look at what Rob from R.I.P.S here in N.Z has done with rb30's, just to name a few, his r32 gts4, rb30det with 100% standard internals and stock r32 rb25de head made 447rwkw and ran a 10.21 @ 134mph and was proven to be very reliable, another r32 gts4 that he built made 400rwkw+ reliably with completly stock internals and also has run numerous 10sec passes.And im sure there a lots more rb30's with stock internals making more power than both of those cars.

2gceffy Rising Star

2gceffy

Posted
Posted (edited)

the guys how did my engine conversion had a 2jz in his 180sx, there was a write up on it in HPI.. had 430rwkw stock internals only had injectors and manifold turbo combo.. was a total beat ran a 10.54 i beleave

i really love both engines so id be happy to own either one

but if i had to bite the bullet id prob hit up the 2jz

Edited by 2gceffy
Cubes Grand Master

Cubes

Posted
Posted
the guys how did my engine conversion had a 2jz in his 180sx, there was a write up on it in HPI.. had 430rwkw stock internals only had injectors and manifold turbo combo.. was a total beat ran a 10.54 i beleave

i really love both engines so id be happy to own either one

but if i had to bite the bullet id prob hit up the 2jz

Heavier VL's with their RB30 SOHC's run 10.5's with bolt ons and a shade over 300rwkw. :S

Cubes Grand Master

Cubes

Posted
Posted

Whats actually wrong with the head?

Small ports/valves?

The port angles/size appear to look ok to me?

http://images.google.com.au/imgres?imgurl=...%3Doff%26sa%3DN

Apparently each port has a slightly different design which makes them a nightmare to work on when porting

Ryanrb25 Grand Master

Ryanrb25

Posted
Posted
You dont need a "purpose built" rb30 to make huge power, just look at what Rob from R.I.P.S here in N.Z has done with rb30's, just to name a few, his r32 gts4, rb30det with 100% standard internals and stock r32 rb25de head made 447rwkw and ran a 10.21 @ 134mph and was proven to be very reliable, another r32 gts4 that he built made 400rwkw+ reliably with completly stock internals and also has run numerous 10sec passes.And im sure there a lots more rb30's with stock internals making more power than both of those cars.

yea all i was getting at was the fact that the rb30det is basically a purpose built thing and not an origional thing. where as 2j is a factory motor doin the same thing.

1JZ head designed by Yamaha. 2JZ by Toyota......says it all really.

Thats why 1.5 JZ (1JZ head, 2JZ block) would be the best combo for power making!

that's very interesting, i would imagine yamaha would have designed the head for revvvving!

also i believe all forced induction toyotas came with forgies....including 3sgte 4agze etc etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • tsuokun
      Lets play a game - What is causing my oil consumption?

      By tsuokun · Posted

      Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
×
×
  • Create New...