Jump to content
SAU Community

Desperately Seeking This Part - Gears Won't Engage.

aaron_25t
 Share

Recommended Posts

aaron_25t Collaborator

aaron_25t

Posted
Posted (edited)

Hey guys,

I need the plastic cap that goes at the end of the shifter. The car I bought (last week) has a C's copy shifter which popped out the other day. On closer inspection I found that this part was split. The car is a 1993 GTS-T R33.

l_cs%20025.jpg

I have tried one Nissan dealership but the parts guy said they can't find the part number for it and hence can't order it.

Having done a search on the forum, a guy with an R32 mentioned he bought one of these for $4 from Nissan....perhaps they don't have this for an R33 or perhaps the guy isn't trying hard enough? I'll keep trying other Nissan dealerships too...

Does anyone have a spare one they want to sell me for a reasonable price? Or even a standard shifter?

If anyone can help out - that would be much appreciated.

Cheers,

Aaron.

Edited by aaron_25t
aaron_25t Collaborator

aaron_25t

Posted
  • Author
Posted

For future reference:

Hi Aaron

Ask the dealer in OZ for part number # 32861 01G00. The small bush fits a number of vehicles which is common through out the Nissan range.

Regards Paul.

Parts Department

City Nissan Takapuna

www.citynissan.co.nz

[email protected]

(B1) MR_fanny Grand Master

(B1) MR_fanny

Posted
Posted

the reason it is split is because the copy shifter does not come with it so you have to use the original one and the only way to get it on is to split it(cut it with a razor or thin hacksaw). im pretty sure if you get a new one you will have to cut it to get it in again.....its a vicious cycle..ha

i have one of these copy kits thats why i know.

mattymagoo22 Community Regular

mattymagoo22

Posted
Posted

it looks like its a pretty common bush that I've seen on a couple of different manual gearboxs mitsu toyota suzuki.

Have you tried a bearing place, look up yellow pages under bearings and bushes and ring around most bearing places sell everything from seals to bolts, bearings gaskets bushes etc etc

If that fails a gearbox specialist may have one lying around.

From memory that bush should sort of clip on eg place it on a sturdy surface put shifter on it then push down firmly, don't think you need to cut it, although I've never fit a short shifter before so you may be right

Hope this helps guys

Cheers Matt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By Murray_Calavera · Posted

      Reading your posts Josh, sometimes I feel like I've gone in a time machine back to the 90's when everyone was doe-eyed and figuring things out for the first time.  I've lost track of how many single turbo GTR's I've seen on track that haven't burnt down lol. Everything has been figured out a long time ago. These things are at the point now where its essentially turn-key to go single turbo. 
    • joshuaho96
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By joshuaho96 · Posted

      Among other things yes. Making sure to either use an oil pressure regulator or the right restrictor size for your oil pump/range of oil viscosities you intend to run, making sure you plumb the lines correctly, turbo should be placed such that it siphons properly even when the water pump isn't turning so you don't boil coolant in the turbo after shutdown, oil return should be low resistance and also preferably picking the one that is most likely to return to the pickup as opposed to some other irrelevant part of the pan. It's far from impossible to figure this out but I have seen people really, really struggle and if that's the case it's easier to just take the path of least resistance. To me, bolt-on twin turbos are a fixed cost whereas single turbo is almost unbounded.
    • Looney_Head
      R32 GTS-t RB30 sedan

      By Looney_Head · Posted

      Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • GTSBoy
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By GTSBoy · Posted

      Ceramic coating and heat shielding, you mean?
    • joshuaho96
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By joshuaho96 · Posted

      Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
×
×
  • Create New...