Jump to content
SAU Community

Recommended Posts

Im planning to have 20+ hicas bars for r32's R33's manufactored if I can get enough interest . These bars could go for as little at 70$ .

If you want one leave your comments,

These will be made at a local engineering shop.

Heres the list

R33 List

1.Ol_Mate

2.75Coupe

3.sam5709

4.MANWHORE

5.madbung

6.Nic19

7.drewr33

8.Silent

9.NickR33

10.LOOF

11.Devils_Advocate21

12lsf_bootz

13.lsf_bootz

14.tek_01

15.Filecon

16.Croat

17.ztuned

18.33SOM

19.JaiJai

20.KeeFy

21.Rhys

22.Zilch*

23.2BNVS

24.dane spec33

25.lvlong

26.mr moo

27.white33gtst

28.MR2MK1SC

29.jeff

30.igota33

31.dr1ft3r

32.arkon

33.performance-wise

34.hazerb30

35.L33igh

36.predator

37.

R32 List

1.MR2MK1SC

2.Adriano

3.1JRocket

4.bubba

5.cln

6.durty2

7.loren

8.gt-t_r34

9.Haysey

10.RB20tR32

11.GTS-4SOME

12.snappy_

13.fazzy

14.

15.

16.

17

18.

19.

20.

Edited by Silent
Link to comment
https://www.sau.com.au/forums/topic/157128-hicas-bars-taking-deposits/
Share on other sites

  • Replies 137
  • Created
  • Last Reply

Top Posters In This Topic

I have a couple ready to be sent already..

$120 delivered via Express Post

Have never had a problem with Quality and strength..

S13/A31/R32/R33/R34..

This is a group by, not the for sale section.

Okay I have 6 people down so far.

well i payed 120 for my bar and it was fairly average. i would have been happy if i payed $70 for it thoe. but seriously you will not get "perftect" unless you pay like $150 out of a shop. hope that doesnt sound like a negative comment but you get what you pay for and sometimes you pay to much.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • OK, that is a helpful description, because that sounds exactly like a bleeding issue in the clutch....these are hard to bleed manually even when the damping loop has been removed. I'd suggest bleeding again....start by filling the master cylinder up and opening the bleed nipple. Come back and check every now and then that the master cylinder is not empty. Let it gravity bleed for a few hours and see if that improves
    • I replaced the whole clutch line with the chase bays braided hose, I think it removes that loop, is it the short hose that comes immediately off the slave or is there a drawing in the manual to find what you’re referring to? It was just re-bled when I upgraded to the nismo slave, old slave worked fine but I thought that might help, didn’t change a thing. It’s like the first half of the pedal is pushing air and then when it finally actuates the master the friction zone is tiny. Makes it practically impossible to launch the car
    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
×
×
  • Create New...