Jump to content
SAU Community

Recommended Posts

  • Replies 561
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Spotlight.. places like big W and such should sell it.. if not.. sew them up!

Hmm I got the fabric from LINCRAFT and I ask what to tape them with and she couldnt suggest anything :action-smiley-069:

Not sure if it will be wide enough

I can get some silver gaffa if needed, it comes in 10mt rolls, how many do you want?

Yes please will need it to go around the outside.... can I have 3 rolls...That should be enough

Cheers Adam

Hmm I got the fabric from LINCRAFT and I ask what to tape them with and she couldnt suggest anything :action-smiley-069:

Ah stupid idiots.. you can get a double sided tape.. fold off the ends and just iron them so they look sharper..

Ah stupid idiots.. you can get a double sided tape.. fold off the ends and just iron them so they look sharper..

Yeah I reckon!

I cant iron them on I have to cut the fabric to size there on site and tape it down

I think I will use clear and Gaffa Tape...and I am going to have to be there early to do it also before all our cars roll in

Yeah good idea lol :action-smiley-069:

Thanks

Yep Malcolm is bringing some too

What time can you get there?

Hold on let me check the diary.. hmm damm boss isnt away..

I can drive to work.. get off say about 5ish and then go straight there.. im might take me like an hour down parra road tho..

Yeah good idea lol :P

Thanks

Yep Malcolm is bringing some too

What time can you get there?

....yeah ill get some double sided for the "warning tape to cone" job - ill be there no later than 1:30 - 2:00 ish - hopefully inside by 4:00 :)

Sinners have pm!!

Yep recieved and replied :P

....yeah ill get some double sided for the "warning tape to cone" job - ill be there no later than 1:30 - 2:00 ish - hopefully inside by 4:00 :)

Hmm im hoping to get off work by 2pm...and go straight there to lay the flooring >_<

Ill be there sometime after 5pm.

Can get there slightly earlier but it means that a friend will have to public transport it out there which she is more than happy to do.Her and her fiancee are more than happy to help out with the setting up side of things.




  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...