Jump to content
SAU Community

Recommended Posts

Yes that is a pig of a hose.

you will need a long set of needle nose pliers to get the clamp off and then spray a tiny squirt of wd40 inside and outside the hose and twist. it will come off.

getting it back on is another story...

yeah, there's no easy way out. You need tiny hands. Try and undo the clamp anyway you can.

Either a long screw driver if you can, or needle nose pliers.

I cut an 8 mm spanner in half and got my hand in (I lubed it up with soap and got it in - yes i was scared i'd never get it back out)

once you get the clamp undone enough, you can get the line out, by pulling the line itself from outside

If you're installing the hks turbo and replacing the line with a braided one, I have no idea how on earth you'll get the new line in.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Been there, done that. Not fun.

Having 2 people to remove it helps, one holds the hose and the other yanks on the metal line.

For install of braided lines atleast you can bend the rubber hose up and fit the barbed end of the braided line, then feed the other end of the line back around the back of the head.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Just hacksaw the metal pipe off, probably as close to the turbo as possible????

I guess I'm worried about metal filing getting in there and also, there would be no lip to stop the pipe coming off..(or would that not be a problem ? )

Have a go ya mug!!!

Actually to tell the truth, mine was held on with the hose clamps that you pinch together with a set of long handled pointy pliers [$10 at Crazy Joes or Micks or somesuch]. The hose was a bit stuck, so I used a long thin screwdriver to work under between the hose and the metal pipe and some WD40 and it came out easy. Don't ask me how to put it back on, I haven't got that far yet..........lol.

PS I don't have a valley cover. that probably made it easier. Actually I found the bolts that screw into the block that hold the stays on this hose harder to get off than the hose.

metal filings are not really an issue wiht that particular hose. That is just a coolant hose, so ti's just the cooling system - just water.

Ther'ell be plentny of shit in there anyways, like everytime I dropped the coolant in my daily driver (not my skyline), there's all rust, and crap that comes out.

Don't get metal in the oil lines though. Totally different story

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

Also, I'd replace that rubber hose at the back. Someone recently, forgot who it was had the hose blow (they're' 10 years old afterall). Better do it now while the turbo is off. Imagine if it blows in 6 months time and having to do it with the turbo on!

If you cut the line, keep in mind that the cooling system is under pressure (up to 0.8bar). Without a bead around the line, the hose can possibly blow off. Imagine having the line blow off on a hot day as you're driving along the freeway. bye bye engine

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

that is wat i did when i replace my turbo with a HKS turbo. and the hks turbo came with a braided line. so i cut it just before the bent.

basicly the same as "Ol_Mate" did!

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

Photos would be great !

So you didn;t need a lip on the end of the pipe with that gland thing?

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Do it right, do it once :happy:

You can do it. Motivational thread for jase. go jase go jase go jase :)

Edited by MANWHORE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Does it make a difference in your turbo having a shorter life if you have a cat converter as it causes that back pressure versus less/no back pressure with a decat? (Not sure if this is accurate) Also slightly different question if you went from a oem cat to a decat or vice versa will it require a tune? I heard if you change the dump pipe onwards it requires a tune?
    • No. Have only gotten as far as contemplating the task of having to put in the required fairly heavy wiring and fusing to run it (along with the big alternator), and preferring not to. But otherwise, it would be nice to have a little extra freedom as to exactly where the compressor is located and free up some space around the exhaust side of the engine.
    • Following from this in a related by not closely-related sense... Because I was buying a bunch of other GKTech stuff, I got some rear subframe collars. The history that leads up to this is: 25+ years ago the car arrived into the country with stock subframe bushes. At some point shortly thereafter I added Whiteline pineapple rings, set up neutral, and it improved the rear end behaviour. Well, it is my vague memory that I was happier with it with them in. Less axle tramp on launches, generally better, etc etc. ~2012 it got a new non-HICAS subframe with new stock bushes. No pineapple rings. I reckon that ever since then I've been dissatisfied with the axle tramp. Recently I've been f**king around a lot with all aspects of the suspension. One contemplation has been to relocate the rear lower control arm front mount points (and do the other things needed to make that work) to improve longitudinal rear grip by getting rid of some of the stupid anti-squat that Nissan ladled into the R32. But.... before doing that I thought I'd put some collars in. And.... The collars are good. The rear sounds a little bit different, but there has been no significant increase in NVH coming up into the body. In terms of rear behaviour - expansion joints on long sweeping elevated freeway ramps that would sometimes cause the rear to jiggle around a bit, no longer seem to do so. It appears that jamming chunks of metal into the gaps in the rubber so they can't move much is a really good thing. And the launch behaviour and general forward traction situation seems to be greatly improved too. It's impossible to be really sure, because the tyres are completely shagged - they are freakishly willing to let go right now. But as an A-B test with the same tyres it certainly seems to grip up a lot better. Highly recommended to anyone who still has stock bushes.
    • Bit off topic maybe but has anyone had a crack at one of those aftermarket electric compressors ? Bit of a search came up with one put out by Speedy Air Spares. Looks interesting and looks as if you'd have to run a big arse alternator. Found this out after the fact as my air con compressor packed it in and soon after my alternator ! !
    • Yes. Needs new ports. Usually just achieved by screwing an adapter onto them. Be aware that any AC compressor that hasn't been used in a long time will very likely have dried out seals and will not hold gas. Oh, and obviously you will require a new receiver-dryer also.
×
×
  • Create New...