Jump to content
SAU Community

Recommended Posts

Hi guys just got my R33 dream car, high grade, factory standard and runs like it has just left the dealership, low kms...or has it? To my disguist I had full inspection done by State Roads in Sydney (where the car is from)and all was well. Car arrives on truck to my house in Adel and when I take it for a cruise all of a sudden I notice trip computer and odometer are not ticking over :D evidence of roll back or is this a common problem when transporting etc?

I'd appreciate all opinions and thoughts guys cos I spent some major cash $21k in fact and if I've been taken for a ride, Consumer Affairs will be notified!

Link to comment
https://www.sau.com.au/forums/topic/158033-odometer-malfunction/
Share on other sites

Hi guys just got my R33 dream car, high grade, factory standard and runs like it has just left the dealership, low kms...or has it? To my disguist I had full inspection done by State Roads in Sydney (where the car is from)and all was well. Car arrives on truck to my house in Adel and when I take it for a cruise all of a sudden I notice trip computer and odometer are not ticking over :D evidence of roll back or is this a common problem when transporting etc?

I'd appreciate all opinions and thoughts guys cos I spent some major cash $21k in fact and if I've been taken for a ride, Consumer Affairs will be notified!

Is it a fresh import?

Not too sure, dealer didn't say it was fresh stock and it got complianced as soon as I bought it.

Oh ok , Does the condition of the car match the kms? Like worn handbrake lever steering wheel etc ( i guess thats the only way to go by), Its very hard to say it could of been turned back here or in Japan, I asshume it has a std speedo.

I think most people accept that if you buy an import the kms would have likely been wound back. When I was getting my car inspected I asked the mechanic whether he thought the kms were genuine. He replied by saying that "anyone who believes imports have genuine kms still believes in Santa Claus." Not that this helps you much i guess...

Edited by ricsvtr
I think most people accept that if you buy an import the kms would have likely been wound back. When I was getting my car inspected I asked the mechanic whether he thought the kms were genuine. He replied by saying that "anyone who believes imports have genuine kms still believes in Santa Claus." Not that this helps you much i guess...

i got genuine log books since new :) cheering

Yea these are some fair points, well interior and engine show signs of a car around the 50,000km mark defintely. I think no matter how much of a pro detailer you are you couldn't get my car in the condition it is if in fact it had 150,000kms.

Only wear is on gear knob, everything else is spotless and I purposely bought the car in stock condition that way chances of being a drift car were reduced.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I think my main complaint with your idea is that there is a veneer of idealism spread across it. You want the simple numbers to make it easier, but all they will do is make it easier for someone to come to the wrong conclusion because the fine details will kick them in the nuts. As it is right now, the tiny bit of arithmetic is NOT the obstacle to understanding what will fit and what will not fit. The reality of trying it is what determines whether it will fit. If you had a "standard rule" that R34 GTT guards have that magic 100mm space from the hub face to whichever side you were worried about, and someone said "excellent, this wheel is only 98mm in that direction, I'll just go spend $4k on them and jam them on my sick ride".....they would just as likely find out that the "standard rule" is not true because the rear subframe is offset to one side by a fairly typical (but variable) 8mm on their car and they only have 92mm on one side and 108 on the other.
    • It still combines inches with mm, especially when you have .5 inches involved, and mm and inches that can go in either direction. This would give a clear idea on both sides of the rim, right away, with no arithmetic. Even better if somebody gives you the dimensions of the arch of multiple cars. i.e GTR may be 125mm, a A80 Supra may be 117mm, or something along those lines. Yes, you can 'know' that going from a 10in rim to a 10.5in rim with the same offset moves both sides about 6mm, but you still have to 'know' that and do the math. Often it's combined. People are going from 9.5 +27 to 10.5 +15. You may do the math to know it, but if it was going from (I had to go look it up to be sure) 241mm/2 - 27 - 93.5mm from the center line to (more math) 266/2 - 15 (118mm) from the center line. Versus 93mm vs 118mm. It's right there. If you know you have a GTT with 100mm guards you can see right away that one is close to flush and the other absolutely won't work. And when someone says "Oh the GTR is 120mm" suddenly you see that the 10.5 +15 is about perfect. (or you go and buy rims with approximately 118mm outward guard space) I think it's safe to say that given one of the most common questions in all modified cars is "How do offsets work" and "How do I know if wheels will fit on my car" that this would be much simpler... Of course, nothing will really change and nobody is going to remanufacture wheels and ditch inches and offset based on this conversation :p We'll all go "18x9+30 will line up pretty close to the guards for a R34 GTT (84mm)" but 'pretty close' is still not really defined (it is now!) and if you really care you still have go measure. Yes it depends on camber and height and dynamic movement, but so do all wheels no matter what you measure it for.
    • But offsets are simple numbers. 8" wheel? Call it 200mm, near enough. +35 offset? OK, so that means the hub face is that far out from the wheel centreline. Which is 2s of mental arithmetic to get to 65mm to outer edge and 135mm to inner. It's hardly any more effort for any other wheel width or offset. As I said, I just close my eyes and can see a picture of the wheel when given the width and offset. That wouldn't help me trust that a marginal fitment would actually go in and clear everything, any more than the supposedly simple numbers you're talking about. I dunno. Maybe I just automatically do numbers.
    • Sure! But you at least have simple numbers instead of 8.5 inches +/mm, relative to your current rims you do maths with as well, and/or compare with OEM diameter, which you also need to know/research/confirm..
×
×
  • Create New...