Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

i drove my mate's 1995 model 180sx the other day with blactop sr20 which is the same engine used in the s14s aswell. it had catback exhaust and pod. honestly, straight line speed wise it felt alot like my parents' VT 3.8 v6. definately not as quick as i thought it would be.....i haven't driven a r32 so can't say which would be quicker...

factory times say both do around 15secs for 1/4 but keep in mind the r32 is a few years older than the s14s. personaly the series2 s14 has one of my favourite front ends, very mean lookin. but the rest of the car is average. and i hate sr20s.

RB20 engine/exhaust note has to be one of the sweetest sounding ever

Edited by R-SPEC

A common misconception is that the blacktop SR20s are all the same. You can basically say that the S13/180SX motors are the same with different cam cover colours.

The S14 (and S15 motors) are different to the S13/180SX motors. Among other things, the S14/S15 motors have -

-Variable Inlet Camshaft Timing (NVCS)

-Larger turbocharger (T28 vs T25G)

-Different inlet manifold setup. (Low port vs High Port)

S15 motors are slightly different again but is of little overall significance.

Cheers :(

stupid question.. this is the type of question that should come from boostcrusing..

sigh.. well basically the S14 is superior, lighter more usable.

180sx S13 red and black are near the same. the S14 and S15 use 28 turbos and have VCT. and high port inlet.

not all s14's have variable cam timing. only the late series 2. you can tell by the lump on the rocker cover.

All S14s have variable cam timing as well as the points i mentioned earlier. How do I know? Because I own both. :(:huh:

but stock they are both slow the s14 and the r32

My r32 when i bought it was stock except for a 3" exhaust but only from the cat back... This exhaust was one of the worst I have ever seen, terrible drone and if anything was causing a loss in power, when i changed it down the track I noticed the difference straight away!

Anyway, with that sh!tter of an exhaust I g'teched my car and ran 0-100km/h in 6.5 seconds. I personally dont consider that slow... but its all in perspective i guess.

My r32 when i bought it was stock except for a 3" exhaust but only from the cat back... This exhaust was one of the worst I have ever seen, terrible drone and if anything was causing a loss in power, when i changed it down the track I noticed the difference straight away!

Anyway, with that sh!tter of an exhaust I g'teched my car and ran 0-100km/h in 6.5 seconds. I personally dont consider that slow... but its all in perspective i guess.

but its not fast

Regardless.... YEARS ago back before SAU was born (2001/2002) I was on SDU. One bloke managed a best of 14.2 1/4 mile out of a dead stock R32 with a good launch and some wide tyres. So not really stock as it wasn't running its stock 205/55/16's :unsure:

---------

lmao... @ 11ty billion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...