Jump to content
SAU Community

My Boot Won't Open -help

MRO

By MRO,
in Four Door Family & Wagoneers

 Share

Recommended Posts

MRO Community Regular

MRO

Posted
Posted

On the weekend i was carrying some paint in the back of my car so i put a towl in the cargo area to protect the boot carpet. After unloading the paint i closed the back door and the towel must have been in the lock area because now i cannot open the back door. I am a bit stuck on how to get the door back open. Any suggestions?

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/158716-my-boot-wont-open-help/
Share on other sites
captinsane Community Regular

captinsane

Posted
Posted
On the weekend i was carrying some paint in the back of my car so i put a towl in the cargo area to protect the boot carpet. After unloading the paint i closed the back door and the towel must have been in the lock area because now i cannot open the back door. I am a bit stuck on how to get the door back open. Any suggestions?

no idea mate...is it worth trying locking and unlocking it a few times - it may make it worse, or it may make it better, i do not know... Don't kill me if it breaks anything though...

Otherwise all i an suggest is undoing the inside panels from inside the boot to get at the locking mechanism.. all the panels should come off...

Or just call a LOCKSMITH???

Appealing Proficient

Appealing

Posted
Posted (edited)

Hmmm I had the same thing happen once with my '92 Falcon wagon. So I know how you feel.

From memory I worked at it from inside, with a kraft knife to shred the cloth, and a screwdriver to pressure the latch. It was a real bitch. The cloth tends to keep the latch closed and the hatch holds the cloth tight. It may help if you have someone on the outside, to push the tailgate in slightly (so that the latch isn't under the same pressure. I know that mine went very suddenly and then just released (opened). Other than that there isn't much that you can do (or a locksmith come to that). The bolts holding the lock on are underneath the lock. So they wont come out with the door in the closed position. Try having someone hold the handle in the open position while you sit down and put pressure on the bottom of the door with your legs. If you can get at the latch you may be ableto trip it with the screwdriver, or you may have to make a "tool" to enable you to do this.

Bear in mind tht it is only jammed. It should give in the end, after a bucket of sweat!

Best of luck.

Tell you what, I bet it NEVER happens again!! :D

I just realised that you are in Perth, (I think). So if you want to come around and see how the lock works and looks while it is in the open position, PM me.

Edited by Appealing
Ska Grand Master

Ska

Posted
Posted

It might also be the auto closing mechanisim that has jammed, this happned to me once when one of the straps of my kids school bags got caught, I just kept pulling it out, like trying to open the rear door from the outside very harshly and eventually it opened.

But I did notice that once the auto closing mechanisim closed it made a wierd sound, and I looked down and saw the strap right where the locking mechanisim is.........

MRO Community Regular

MRO

Posted
  • Author
Posted

Finally got it open. I must admit i did not try to hard as i havent needed to use the boot too much recently.

I got it opened by getting my wife to push the door from the inside while pulling back on the towel. I was on the outside lifting hard on the handle.

The self closing mechanism doesnt help because normally you would notice this kind of thing when closing the door. As you dont have to slam the door shut it is not until it is too late you notice something is jammed in there.

Topkart R33 Community Regular

Topkart R33

Posted
Posted

For future referances all you need to do is take the plastic trim around the window off, then the locking caps for the carpeted trim and access latch from there. Push down on the part with the yellow bush which has the push rod attached.

  • 3 years later...
Stooge007 Rising Star

Stooge007

Posted
Posted

For future referances all you need to do is take the plastic trim around the window off, then the locking caps for the carpeted trim and access latch from there. Push down on the part with the yellow bush which has the push rod attached.

sorry to bump an old thread, but something is caught in my C34 boot latch, and it won't open

as far as i can tell, you can't take any boot trim off as you can't access any of the screws/pop rivet things?

will try just forcing it open with my feet from the inside (while someone is outside holding the latch open, but putting pressure on the boot toward the car???)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Let's hope that's not a copy pump either. There were so many copies of them back in the day.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Dose Pipe Sutututu
      Hypergear Turbochargers and High flow Services Development thread

      By Dose Pipe Sutututu · Posted

      Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
×
×
  • Create New...