Jump to content
SAU Community

R32 Coupe Seats In Sedan

CeJay

By CeJay,
in Exterior & Interior Styling

 Share

Recommended Posts

CeJay Grand Master

CeJay

Posted
Posted

Tried putting mine in tonight, the coupe seats seem to be 5cm shorter from each outer body hook to the metal loops where you bolt the seat in, just couldn't get them in. Anyone else done em before? The whole seats just seem a bit too short. Plus I didn't want to bend the three rear hooks anymore.

Link to comment
https://www.sau.com.au/forums/topic/159090-r32-coupe-seats-in-sedan/
Share on other sites
grandmasterb Grand Master

grandmasterb

Posted
Posted
Tried putting mine in tonight, the coupe seats seem to be 5cm shorter from each outer body hook to the metal loops where you bolt the seat in, just couldn't get them in. Anyone else done em before? The whole seats just seem a bit too short. Plus I didn't want to bend the three rear hooks anymore.

Had the same problem when i was going through compliance with one of mine. They wont fit and its not worth bending the hooks.

Swap them for the right ones and save yourself the hassels :happy:

  • 2 weeks later...
CeJay Grand Master

CeJay

Posted
  • Author
Posted

hmm well since I've just been quoted 1100 dollars to reupholster the rear seat and door inserts, has anyone modified the coupe seats to fit in the sedan? Or anyone know if the 4 door r32 ever came with the better upholstery in it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...